To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.

Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.

Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.


When the shelf was full, we called the list done. The results of that debate is the list of books that follows (publishers listed are for the editions we own). It’s by no means a perfect list. It is a list that would probably change a bit if we had the debate again in a couple months. Some of these are classics, some are contemporary. But these are the books that are first in our hearts.
But I still wasn’t entirely satisfied with our list. I wondered if we’d read enough woodworking books as a staff to create a solid list. So we surveyed the readers of my blog (the results of that are on our web site), then asked many of the woodworkers who write for us to contribute lists of their favorite woodworking books. Theirs are below, in their own words (publishers have listed only on first reference; but if no publisher has been noted, the book is available on Google Books at books.google.com).
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.

The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.

Contrast is created when you have two or more related elements that are different. Contrast can be used to add visual interest, depth and to highlight a dominant element. It is also a way to unite a piece and often bestows energy to a design. If there are too many contrasts or the differences are too severe, there is risk they will not only compete for attention, but may also create unbalance, confuse the viewer and create optical illusions. To achieve success with contrast, ensure the differences are obvious enough, but without an overpowering presence. Each design element mentioned in this article can be manipulated to create contrast. Each of the images not only relate to the corresponding element but also exhibit contrast.


This book was put together to introduce people to the world of carving, and I think it does a great job. Starting with tool selection, sharpening and other important, but often overlooked as­pects of the craft, it moves on to discuss chip, relief and sculptural carving. With a chapter on surface decoration as well as a section of scaled patterns to get you started, this book has a bit of everything. And even if you’re not interested in traditional carving projects, the skills learned in this book will introduce you to techniques that can be used to add texture to your next furni­ture project.
This bench suffers from no such limitations as it provides an incredibly solid and stable workspace, albeit in a somewhat stripped down version. In terms of performance, Sjobergs tops our list at providing 80 lbs of weight capacity. This is one of the more quantifiable measurements to determine the quality of a work bench’s craftsmanship. This is achieved by using thick pieces of European birch wood and working it without using lower end joints – like butt joints.
×