If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?

Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!
Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
5. The Woodbook: The Complete Plates. This one contains no instructions, no techniques, and no how-to information. Rather, it's the most complete collection of American wood samples ever created. Assembled between between 1888 and 1913 by New Yorker Romeyn Beck Hough and originally published in fourteen volumes, Taschen's publication "reproduces, in painstaking facsimile, all of the specimen pages from the original volumes... For all trees, now arranged in alphabetical order, three different cross-section cuts of wood are represented (radial, horizontal, and tangential), demonstrating the particular characteristics of the grain and the wealth of colors and textures to be found among the many different wood types. Also included in this special edition are lithographs by Charles Sprague Sargent of the leaves and nuts of most trees, as well as texts describing the trees’ geographical origins and physical characteristics."

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.

My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.


Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
The Woodworker's Library™ offers hundreds of books, plans, and videos on topics related to woodworking, arts and crafts, home improvement, woodworking tools, furniture, and much more — many at discount prices. We make every effort to keep our catalog up-to-date in order to offer you the widest selection of quality titles to choose from. Browse our extensive book catalog and shop online. We hope you enjoy your visit.
First, cut one long edge. Second, cut a short edge, making sure it's square to the long edge you just cut. Clamp both pieces of the edging you'll be using along the long edge you've cut, and measure the width of the base plus 1/4-1/2", mark that, and then lay out a line through the mark that is square to the end you've cut, then cut along the line. Finally, cut the remaining short edge square to both long edges. (The length of the top doesn't need to precisely match anything, so we don't need to bother with clamping the trim before measuring.)

Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
×