Finishing is often an afterthought and spraying a finish isn’t exactly the first technique discussed when the topic does come up. While it’s often easier to wipe on a couple of coats of finish and be done with it, there are times when spraying a finish makes the most sense. There are many advantages to spraying a finish but there are some drawbacks too. Spray Finishing Made Simple does what it claims – it takes an imposing, unfamiliar topic and makes sense of it. This book is for the first-time spray finisher, as it starts with the basics and progresses through the stages. Don’t let the unknown stand in your way if you’re interested in learning about spraying. Pick up this book and get spraying.

Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!

Many kids have the natural desire to learn about tools and make wooden objects, but as adults it’s difficult to know where or how to start teaching. Kid Crafts Woodworking starts at the very beginning, with short sections on, among other things, the proper­ties of wood, gluing and metal fasteners. Nothing long or boring, just the basics, for a kid-length attention span. With straightfor­ward paragraphs and clear, simple photos, the book goes on to discuss the safe usage of basic tools. Then comes the fun part – the 21 projects. Easy-to-follow instructions will guide your child through the projects, but there’s no reason why you shouldn’t be there every step of the way. Just don’t get too eager and do all the work for them … it’s their project after all.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Drill a pair of 3/8" holes in each end of the short stretchers, just over half of the depth of the dowels, using a brad-pointed bit. These stretchers already have a groove running their length, centered on the bottom edge. Precise placement isn't necessary, but keeping track of which part is which is. We need a hole in each end of each stretcher. Take care to keep these holes square, you don't want them running at angles.

Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
×