To develop the material, we editors asked ourselves—and dozens of top woodworkers—what’s likely to go wrong at each stage of a project. We really dug deep to make sure we didn’t just repeat the types of advice you see in the average magazine. We ended up with a list of more than 500 problems covering everything from design and layout, to stock preparation, joinery, finishing and more. Then, we reached out to top woodworkers around the country for their solutions. The result was a 320-page book filled with some of the best advice you could ever find from more than 75 master craftsmen, including Marc Adams, Mike Dunbar, Graham Blackburn, Toshio Odate, David Marks, Frank Klausz and Lonnie Bird.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
There are two books that I would consider highly influential in my personal woodworking path. Darrell Peart’s “Greene & Greene: Design Elements for the Workshop” (Linden) and “Adventures in Wood Finishing” by George Frank (Taunton). Peart’s book kicked off my fascination with all things Greene & Greene. Peart does a fantastic job of covering history as well as practical techniques.
Featuring each piece in highly-detailed, exploded drawings and applying time-honored dimensions and ergonomic standards, this comprehensive visual sourcebook takes the guesswork out of furniture joinery, assembly, dimension, and style. Woodworkers of any skill level will benefit from more than 1,300 crisp and detailed drawings that explain classic solutions to age-old problems, such as hanging a drawer, attaching a tabletop, and pegging a mortise.”
Another comprehensive book by Taunton Press, Wood Flooring is extremely informative, not to mention visually compelling. From subfloors to finishing, and everything in between, you can be sure this is the only book you will ever need on the subject. My favourite chapter was on inlays and curves: using jigs and templates to add circular inlays to a floor, laying out and installing laminated curves, even working with stone and metal inlays … there’s a lot to learn in that one chapter alone. Much of it could be adapted to making furniture. If you want to lay a basic wood floor this book will help you add lasting value and beauty to your home. If you’re looking to one-up your super handy DIY brother-in-law, you can start here too.
“With Hammer in Hand” by Charles F. Hummel (UP Virginia). Resurfacing like Brigadoon, the woodworking shop of the Dominy family was sealed up with the tools still on the benches and saws still sharp. Moved to the Winterthur Museum, the workshop is an open portal into village woodworking in early America. Hummel’s book takes it tool by tool, piece by piece, expanding our view with a true scholar/craftsman’s eye.
We will charge the payment method listed in Magazine Subscription Manager. If we cannot successfully charge this payment method, we will use the payment method you gave us when you originally placed your order. If we cannot successfully charge that payment method, we'll use another payment method you have saved in your Amazon.com account. Your initial sign-up is an authorization for us to use the preferred or other available payment methods to pay for your subscription.
I was raised by crafty people. In every sense of the word. Just kidding! My parents were lovely people who loved to work with their hands in their spare time. For a brief period of time as a kid my mom even earned a living by selling her wares at local craft fairs, but for the most part their crafting was a hobby that filled our home with beautiful and practical pieces of woodworking.
Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
Woodworking books, plans and CDs allow you to study the methods of woodworking experts to reduce the learning curve on woodworking projects and save valuable time in the workshop. Reading a woodworking book is the easiest and least expensive way to learn from woodworking legends and craftsmen. Woodworking tips and lessons from masters like Tage Frid, Frank Klausz, Sam Maloof, Thomas Moser, Ian Norbury, Toshio Odate, Rude Oslnik, David Pye, and Gustav Stickley can be right at your finger tips. If your are interested in improving your hand tool skills or learning classic furniture-making techniques, we find Lost Art Press Books to be among the most important woodworking book collections we offer. With Christopher Schwarz as part of the writing and publishing team, you will be gaining access to one of the most creative and knowledgeable woodworkers around.
Projects to build on. Korn's book includes basic projects that you can put your own spin on. This Shaker footstool was inspired by one of the projects in his book. The last side-table project in his book (pictured) has the same pedigree as these two other FW projects: Tim Rousseau's small cherry cabinet and Stephen Hammer's small stand with coopered panels.
Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).
Originally published at the turn of the twentieth century by an anonymous “Practical Joiner,” Woodwork Joints: How to Make and Where to Use Them remains an incredibly useful and practical guide for deciding which joints to use and how to make them the right way for carpentry, joinery, and cabinet-making. Here is the carefully illustrated source on joinery that not simply a collectible classic, but also a requisite and invaluable tool that withstands the test of time, containing more useful information than any other woodworking guide. Inside are illustrated instructions for making all kinds of joints, from simple to complex, suitable for novices and experts. The comprehensive list includes joints such as glued; halved; bridle; tongued and grooved; mortise and tenon; dowelling; scarf; hinged; shutting; dovetail and many more. Instructions specify which tools are required (i.e., planes, gauges, saws, chisels, the try square for testing purposes, etc.) and how to use them on each joint. Extensive chapters on each type of joint contain precise illustrations that make identifying joints for different purposes easy. Not a word is wasted in this short but entirely comprehensive guide, making Woodwork Joints the perfect aid for any joinery project.
My woodworking mentor, Robert Van Norman, studied under the esteemed woodworker James Krenov. Robert remembers many of JK’s wise words, especially “trust your eye”. When it was time for me to hear those words, I remember feeling such relief and permission to embrace my inherent perspicacity. Intuition is essential in the design and creation process, and for developing work that reflects the maker beyond his or her technical skill alone. At times, the craftsperson is called on to explain the aesthetics of his design and saying “it just feels right” doesn’t always cut it. This article covers seven common design considerations, their definition and how they are generally accepted and understood. Not only will the article help increase design vocabulary and awareness, but it may also assist in problem solving and recognizing the aesthetic strengths and weaknesses of a furniture piece.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
When the shelf was full, we called the list done. The results of that debate is the list of books that follows (publishers listed are for the editions we own). It’s by no means a perfect list. It is a list that would probably change a bit if we had the debate again in a couple months. Some of these are classics, some are contemporary. But these are the books that are first in our hearts.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.