Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.
Originally published at the turn of the twentieth century by an anonymous “Practical Joiner,” Woodwork Joints: How to Make and Where to Use Them remains an incredibly useful and practical guide for deciding which joints to use and how to make them the right way for carpentry, joinery, and cabinet-making. Here is the carefully illustrated source on joinery that not simply a collectible classic, but also a requisite and invaluable tool that withstands the test of time, containing more useful information than any other woodworking guide. Inside are illustrated instructions for making all kinds of joints, from simple to complex, suitable for novices and experts. The comprehensive list includes joints such as glued; halved; bridle; tongued and grooved; mortise and tenon; dowelling; scarf; hinged; shutting; dovetail and many more. Instructions specify which tools are required (i.e., planes, gauges, saws, chisels, the try square for testing purposes, etc.) and how to use them on each joint. Extensive chapters on each type of joint contain precise illustrations that make identifying joints for different purposes easy. Not a word is wasted in this short but entirely comprehensive guide, making Woodwork Joints the perfect aid for any joinery project.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)
This book addresses a key dilemma of the beginning woodworker: how do you build good projects without the basic shop furnishings to get the job done? And, why struggle with makeshift workshop equipment when you can create your own? Now you have the guidance of an expert woodworker to help you build workshop basics that you will use for years to come.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
Featuring each piece in highly-detailed, exploded drawings and applying time-honored dimensions and ergonomic standards, this comprehensive visual sourcebook takes the guesswork out of furniture joinery, assembly, dimension, and style. Woodworkers of any skill level will benefit from more than 1,300 crisp and detailed drawings that explain classic solutions to age-old problems, such as hanging a drawer, attaching a tabletop, and pegging a mortise.”
In order to complete your transaction, we will share the name, billing and shipping address and other order information associated with your purchase with the publisher or magazine vendor. Your name and address will also be shared with a circulation-auditing organization. We may share your e-mail with the publisher, but you can control how it will be used in Subscription Manager. We will not share your credit card information. Offers on this page are introductory. See Details.
Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.
I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
You can bookend my 30 years of woodworking with two volumes. Roy Underhill’s “The Woodwright’s Shop: A Practical Guide to Traditional Woodcraft” (U of North Carolina P) marks the beginning. Today, Steven W. Semes’ “The Architecture of the Classical Interior” (Norton) makes sense of all the conflicting mishmash of “design speak” tossed about. Hope I have another 30 years in me so the Semes book will someday be a midway milepost in a long, rewarding journey.
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
When this book showed up at my studio I was very sceptical. Yet another “book of everything”? But after spending only five minutes skimming through it, I learned about a couple of storage ideas my shop needed, some cool new jigs that would come in handy and a few tricks to make my time in the shop more enjoyable and productive. There will be hundreds of ideas in here you will have no interest in whatsoever, but that’s all right … there are over 650 ideas in total, so some are sure to tickle your fancy.
Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.