Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference

This gem starts with a wink that’s explained further down on the cover: “Three Practical Ways to Do Every Job—and how to choose the one that’s right for you.” Bob introduces the main woodworking processes from dimensioning stock, to cutting dovetails, and then offers a variety of ways to get the job done using traditional hand tools, modern machinery, and an assortment of slick jigs.


For those who would like to have the benefit of a woodworker’s extensive experience with hand tools, this is the book to own. Crammed with practical information, it is the next best thing to looking over a craftsman’s shoulder as he works with his tools, asking questions and getting straight answers in plain language, seeing how each tool is held and manipulated to get the best work out of it. From bit brace, chisel, and mallet to saws, specialized planes, drawknife, and spokeshave, Aldren Watson describes in detail the actions of the tools basic to good woodworking. All the procedures are explicitly illustrated with handsome line drawings, and an appendix gives plans and dimensions for making a workbench and other necessary pieces of shop equipment.”
Cabinetmaking at the highest level is an art, a discipline, a philosophy–even a way of life–in addition to being a useful craft. In this book one of the greatest living cabinetmakers reflects on the deeper meanings of his craft and explains for less accomplished workers how the right attitudes toward materials, tools, and time can increase the joys of this complex activity. Craftspeople in every medium will be inspired by this account of getting started and developing habits that lessen the difficulties of a complex craft.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
If you’re looking for something fun, funky and functional, you’ll find it in your Kotula’s catalog. We’re relentless in our pursuit of the good stuff which means you can count on your Kotula’s catalog to be your personal cornucopia of cool. Kotula’s has gifts and gizmos, tools and time savers, low prices and great value. Request your free catalog today.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!

Penland School of Crafts has been operating in the foothills of the Blue Ridge Mountains for over 75 years. This book details how ten instructors – all experts in their fields – make some of the furniture for which they are best known. Each instructor is vastly different from the next, and the tips they detail are highly innova­tive yet understandable and useful to the amateur woodworker. The director of the school, Jean McLaughlin, says the aim of the book is threefold. “To give the reader insight into the creative and technical processes of leading woodworkers, to provide detailed, intermediate-level technical information, and to showcase a range of approaches to the material.” The book excels on all three levels. Even when Istrongly disliked the style of furniture being discussed, revelled in the unique approach the maker took to break new ground to complete the finished piece. If you would like to see how one-of-a-kind pieces of studio furniture are made, and start to add some new techniques to your arsenal, either take a trip to North Carolina or pick up this book. 
I marked out the one hole location, drilled a shallow 1/16" hole into the top. I then put a 1/16" bit through the hole in my template and into the hole I had just drilled. I lined up the template, and drilled a second hole, then put another bit through that. From then on, I worked entirely from the template. With two bits through the holes pinning the template in place, the other holes in the template would be precisely located (or so the theory goes) on a 4x4" grid.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
×