With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
Our understanding of what makes pleasing proportion is deeply imprinted in our mind and of all the design elements is the least influenced by one’s cultural experience. Desirable proportion has long been based around ratios we see in nature with an emphasis on the human body. The “golden rectangle,” considered to be divine proportion, has been used since at least the Renaissance period in art and design and has largely influenced our common experience with architecture and design. In fact, we often don’t even see proportion until something is out of proportion.
The Joint Book contains easy-to-follow step-by-step instructions for creating edge and scarf joints, lapped and housed joints, mortise and tenon joints, miters and bevels, dovetails, dowels and biscuits, and provides detailed descriptions of fasteners, hardware, and knockdown joints. This book is the perfect companion for any woodworker interested in improving their joint-making skills.”
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.

All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.

If you’re looking for something fun, funky and functional, you’ll find it in your Kotula’s catalog. We’re relentless in our pursuit of the good stuff which means you can count on your Kotula’s catalog to be your personal cornucopia of cool. Kotula’s has gifts and gizmos, tools and time savers, low prices and great value. Request your free catalog today.


We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
I am surprised the the Hand and Eye combo by Tolpin didn’t make anyone’s list. I have also really found Chris Schwartz’s Anarchist’s design book very useful. Everything else that I really like is already in here somewhere; Moxon, Roubo, Estonia, Peart. The beginners book by Wearing is excellent, and I have taken to giving it to Eagle scouts at their Eagle Courts of Honor of late. (with an inscription about taking the raw stuff of life and developing the skills and tools to make from it what you need…); cheesy, I know, but it is a really good book to start folks off with.
Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
1. Cabinet Making and Millwork by John L. Feirer. I read this book cover to cover when I first got into woodworking, and its still my number one reference book when researching a project or technique. I believe it was intended as a textbook for a high school shop class, so it's laid out in great 101 style. It includes descriptions of everything from how sandpaper is made to best practices for shop math, and provides details for both hand and power tools.
Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
In order to complete your transaction, we will share the name, billing and shipping address and other order information associated with your purchase with the publisher or magazine vendor. Your name and address will also be shared with a circulation-auditing organization. We may share your e-mail with the publisher, but you can control how it will be used in Subscription Manager. We will not share your credit card information. Offers on this page are introductory. See Details.
Woodworking Workbenches are available in a variety of styles. Open Style Wood Workbenches feature a large work surface and a lower shelf. 2-1/4" thick maple top with maple plywood lower shelf. Open Style Wood Workbenches are available as a 2-station unit (28"W) or a 4-station unit (54"W). Open Style Auxiliary Workbenches are used for placement against walls. Shelf features a rear curb to keep contents in place. Solid maple top features angle iron front edge. Plywood shelf is open for maximum functionality. Solid maple legs. Environmentally-friendly UV finish. Units measure 24"D and are available in several lengths and heights. Mitre Box Benches ensure wood pieces are kept flat while mitres are cut. Bench is made using solid maple unit with environmentally-friendly UV finish. Holds a mitre saw up to 26"W and provides a 24" square work surface on both sides. Mitre Box Benches measure 33-3/4"H. Sheet Metal Workbenches are made with a 2-1/4" thick maple top and is protected on two long edges with 2" x 2" angle iron. Solid maple legs and stringers. Plywood shelves are designed to provide open storage of 30" metal sheets. Measures 40"D x 32"H and available in widths of 60" or 96".
If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.

My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.

Pyrography Workbook: A Complete Guide to the Art of Woodburning. It’s amazing what you can create with woodburning. You can make art that stands on its own, or use woodburning to personalize your crafts. In her book, Sue Walters talks about equipment, techniques, and safety. She also takes you step-by-step through 3 different projects for the beginner, intermediate, and the advanced woodburner. When I bought my first wood burner, I automatically purchased this book as well.

Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.

“This hardcover book with internal spiral binding is 6.5in x 8in, a perfect size for carpenters and woodworkers to keep near their workbench or toolbox for quick access.The design of this book allows it to lay open flat, which allows for easy and frequent reference, and the interior photographs, illustrations and diagrams, make the learning process simple and fun for beginners, and provides useful tips for more advanced readers.
If you’re even the slightest bit interested in the history of Japanese furniture, you will love this thorough collection of chests. The attention to detail is astounding, the photographs glorious and the historical insight intriguing. This is exactly what you would expect from a book that covers such a proud history of chest mak­ing on the land of the rising sun. Almost 100 pages of colour plates are complemented by information on typical construction materials, finishing techniques and regional charac­teristics. This book will please the antique collector, interior designer or wood­worker equally. 

The original design had a height of 35-1/8". Their two-layer top was 1-1/2" thick, so their legs were 33-5/8" long. I want a height of 35", but I'm using a top that's 3" thick. My basement floor is anything but level, so I'm using levelers that are adjustable from 3/4" to 1-1/2". In other words, I want legs that are around 31-3/4" long. (If you're not using levelers, your legs need precise lengths. The levelers give about 3/4" of adjustment, so precision is less necessary.

While our website has the most comprehensive list of all of our tools, sometimes it's nice to flip through the pages of a good old fashioned catalog.  This contains only our most popular permanent products that we manufacture just outside of Cleveland, OH.  We will be happy to send you one at no charge.  Just click the order button below so we can get the address you would like it sent to.  


I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
Stop it. Really. I mean it. Pick a height between your thigh and waist that seems right. You’ll adapt. Don’t worry about your back. You’ll adapt. If you are really uncertain, make it a little taller and then cut down the legs. After a decade or so, your work habits will put a magic number in your head. You’ll have built enough furniture that you will know your number. Until then, pick a number.
×