The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
“With Hammer in Hand” by Charles F. Hummel (UP Virginia). Resurfacing like Brigadoon, the woodworking shop of the Dominy family was sealed up with the tools still on the benches and saws still sharp. Moved to the Winterthur Museum, the workshop is an open portal into village woodworking in early America. Hummel’s book takes it tool by tool, piece by piece, expanding our view with a true scholar/craftsman’s eye.
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
A bewildering variety of tools, clever marketing copy, and lack of knowledge can lead even the most determined new woodworker to make many unnecessary purchases, causing frustration or retreat. Written for true beginners, Your First Shop offers inspiration and encouragement, guiding readers toward smart tool choices by providing realistic, reliable information. Best-selling author Aimé Ontario Fraser started working with wood in high school, and has taught extensively in workshops and classes since. Your First Shop brings that experience to readers. Woodworkers of every taste can find a shop style that works for them in one of the book’s four sections: The Essential Shop, The Basic Shop, The Efficient Shop, and The Well-Rounded Shop. Topics include how each tool is used and what it is used for. The book also offers extensive advice on choosing a location for the shop, maximizing available space, and planning for future expansion.
Being a lover of Japanese design and tools, I’m embarrassed to say I only picked this book up in the last year. I was anticipating a straightforward, almost encyclopaedic, approach documenting the history and use of most Japanese woodworking tools. I got that, but also so much more. The stories Odate tells of his youth and apprenticeship are truly jaw-dropping, and reveal as much about working wood in Japan as what life in a fascinating and secluded Pacific country was like when he was young. I was five minutes into this book, and I guess I had an astonished look on my face, when my wife politely asked how I was enjoying the book. I looked up in bewilderment, paused for about five seconds, and said “It would take me an hour to explain what I’ve learned in the last five minutes,” and went on reading. Even though this book has been around for decades, it’s worth reading today.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
The person who coined the saying, “The more things change, the more they stay the same,” just might have been a woodworker. Admittedly, new tools and materials have made certain operations faster, safer, and easier, but if a woodworker from the 1900s could visit your workshop, he’d have a tougher time with the K-cup coffeemaker than the table saw. That’s because the basic tenets and tools of woodworking are almost timeless.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.
Grizzly is a company currently undergoing an upheaval. This brand was once known as a manufacturer of professional grade tools and equipment for woodworking products. Though, in recent years, that reputation has begun to slip a bit since being bought by the Chinese company SIEG. These days, whether the Grizzly product stands up to its previous standards of excellence often has more to do with what you are buying than the company itself.