The Joint Book contains easy-to-follow step-by-step instructions for creating edge and scarf joints, lapped and housed joints, mortise and tenon joints, miters and bevels, dovetails, dowels and biscuits, and provides detailed descriptions of fasteners, hardware, and knockdown joints. This book is the perfect companion for any woodworker interested in improving their joint-making skills.”
“With Hammer in Hand” by Charles F. Hummel (UP Virginia). Resurfacing like Brigadoon, the woodworking shop of the Dominy family was sealed up with the tools still on the benches and saws still sharp. Moved to the Winterthur Museum, the workshop is an open portal into village woodworking in early America. Hummel’s book takes it tool by tool, piece by piece, expanding our view with a true scholar/craftsman’s eye.
Woodworking Books go hand in hand with the tools and the work. Whether you are a beginner or a master woodworker there is always a new technique or a great tip waiting for you on the pages. We have hundreds of woodworking books to choose from, written by woodworking authors who understand the craft and know the trials and tribulations of the path.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.
The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.
Once you've placed an order at Amazon.com, it can take one to two weeks for your subscription to be received and scheduled by the publisher. Your subscription is then added to the publisher's next production cycle and shipped via standard mail. For example, if your monthly subscription was ordered and received by the publisher in November, and the December issue has already shipped, your order may be added to the January mailing. You can find out more information, including how to contact the publisher about your subscription, in Amazon's Magazine Subscription Manager.
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.
The Real Wood Bible I love to pull this book off my shelf from time to time and learn about different characteristics of a certain wood. What’s the wood used for? How easy is it to turn? Toxicity? It’s a very useful book with lots of great photos. Let’s say you have a piece of wood you need to identify. The photos are very crisp and defined so you can match a wood you possess to one found in the book.
Dark colours appear heavier and create a feeling of stability, whereas light colours hold less visual weight and can appear unstable. When joining woods of dark and light colour, the visual effect of heavy and light suggest that darker woods work better when used on the bottom. A suggestion from my mentor to help getting proportions right was to spray paint mock-ups with a colour similar to the woods to be used later.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Skirting traditional woodworking – sometimes seemingly allergic to it – this book shows you things you didn’t think were possible with wood, and many things you wish you had thought of first. The variety of the finished pieces is wonderful and makes for a nice read. Including 89 artists in total, each brief section contains background information, inspirational thoughts and technical details on how each artist completes their work. Wood Art Today 2 covers furniture, turnings, boxes, sculptures and more. One of the things I like most about it is you can open it up to any page and start learning about a specific artist and the work they do. This one is a lot of fun.
Woodworker’s Visual Handbook. This is a book for people like me, who can understand an idea faster if they see it than read about it. Woodworker’s Visual Handbook has more than 1,300 illustrations and 430 pages of advice that visually explain such issues as how to install smooth-sliding drawers in frame-and-panel cabinets, how to lay out a complicated project and cut the joints, and the pros and cons of working with more than 60 species of wood (a topic on which author Jon Arno was an expert). There’s even a section on furniture styles, another topic Jon knew well.
These sorts of things are usually glued and screwed, but it's actually the glue that holds them together - the screws just hold everything tight while the glue cures. Screwing into hardboard or 1/4" ply is an exercise in futility, so I just used glue, and used my two 4x4's as long clamps. It would have been a bit easier, if I'd done this before I'd rough-cut the 4x4's, but it worked out.
When the shelf was full, we called the list done. The results of that debate is the list of books that follows (publishers listed are for the editions we own). It’s by no means a perfect list. It is a list that would probably change a bit if we had the debate again in a couple months. Some of these are classics, some are contemporary. But these are the books that are first in our hearts.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.