New information on composite materials, adhesives, and finishes brings this book into the 21st century, while more than 300 photographs bring important visual information to life. This edition covers the nature of wood and its properties, the basics of wood technology, and the woodworker’s raw materials. Understanding Wood was written for woodworkers by a scientist with a love of woodworking. It will be sought after by craftsmen and collectors alike.”
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.

We offer top quality woodcraft products. When it comes to quality, dedication and a commitment to excellence we can't be beat! We have a large selection of online craft supplies for the hobbyist or the professional woodcrafter. We're dedicated to meet your craft and woodcraft products needs. Check out our online store and let us help you make your next woodcraft projects shine!


Our understanding of what makes pleasing proportion is deeply imprinted in our mind and of all the design elements is the least influenced by one’s cultural experience. Desirable proportion has long been based around ratios we see in nature with an emphasis on the human body. The “golden rectangle,” considered to be divine proportion, has been used since at least the Renaissance period in art and design and has largely influenced our common experience with architecture and design. In fact, we often don’t even see proportion until something is out of proportion.
We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.
Tapping the knowledge of dozens of top-shelf woodworkers, Scott Landis’s The Workbench Book, and Jim Tolpin’s The Toolbox Book are filled with inspirational photos and drawings that you can use to enhance your workbench and tool storage needs. John White’s Care and Repair of Shop Machines completes the workshop triumvirate. The author’s straightforward advice for repairing and setting machinery will help you make the most of every machine in your shop.
I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
“This hardcover book with internal spiral binding is 6.5in x 8in, a perfect size for carpenters and woodworkers to keep near their workbench or toolbox for quick access.The design of this book allows it to lay open flat, which allows for easy and frequent reference, and the interior photographs, illustrations and diagrams, make the learning process simple and fun for beginners, and provides useful tips for more advanced readers.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.

Before you start cutting or drilling the pieces that will make up the top, determine the layout of the top. This should include the dimensions of the MDF, the dimensions of the edging, the locations of the vises, and of the screws or bolts that will support the vises, and of all of the benchdog holes and of all of the drywall screws you will use to laminate the panels,
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.

Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.


For the most part, furniture restorers/refinishers/conservators in the United States lack the necessary hand-tool skills to do proper wood repairs. But avid readers of Popular Woodworking Magazine do possess the skills. Like me in the 1970s, you just need instruction on how to go about it. These books provide this. They greatly influenced the techniques I use in my shop, and many are shown in the “Repairing Furniture” video/DVD I made for Taunton.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.

This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Another aspect that might irk some buyers is the fact that the capacity of this bench is less than great outside of weight. The top’s surface area is a bit on the smaller end, though its length is more in line with larger models. The width though is less than two feet which can limit some projects. Similarly, the vice capacity is the second smallest on our list at 4 ½”, though this too can be modded with optional additions.
×