Line is defined by two points and is long relative to its width; it can be thick, thin, vertical, diagonal, straight or curved. Lines are often used to define a space, draw attention to a particular area and guide the viewer's eyes around a piece. To critically examine line in your design, look at the relationship between the lines, including ones which may be created in the negative space. How do they align? Do they lead your eye around the piece or do they stop abruptly and create disorientation?
The Fall 2018 issue of Scroll Saw Woodworking & Crafts features a variety of projects, patterns, and features, as well as interesting techniques. This issue is a part of the regular magazine subscription. It is also available from your favorite retailer or from Fox Chapel Publishing,www.foxchapelpublishing.com, 1-800-457-9112.   In This Issue Scroll down for a […]
This is a beautiful and inspiring book for anyone who wants to broaden their horizons when it comes to turning.  Not a how-to book, it talks with over 30 world-renowned turners about their approach to the craft, and what keeps them motivated to push the boundaries and create exquisite pieces of art.  You will learn more about the makers’ vision than how they produced their stunning works of art.  I read every word of this book and studied every single photograph, and was completely enthralled the entire time.  And I’m not even a turner!  This book is for anyone serious about turning, or woodworking in general. 

Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
My woodworking mentor, Robert Van Norman, studied under the esteemed woodworker James Krenov. Robert remembers many of JK’s wise words, especially “trust your eye”. When it was time for me to hear those words, I remember feeling such relief and permission to embrace my inherent perspicacity. Intuition is essential in the design and creation process, and for developing work that reflects the maker beyond his or her technical skill alone. At times, the craftsperson is called on to explain the aesthetics of his design and saying “it just feels right” doesn’t always cut it. This article covers seven common design considerations, their definition and how they are generally accepted and understood. Not only will the article help increase design vocabulary and awareness, but it may also assist in problem solving and recognizing the aesthetic strengths and weaknesses of a furniture piece.

The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.


The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.
Shape is critical to the ultimate success or failure of a piece of furniture. Knowing this, custom-furniture maker Lonnie Bird has taken the complex subject of shaping and in this book made it accessible to every woodworker. He guides the reader toward first visualizing, then drawing a shape, and then choosing the appropriate tool for creating it. Shaping techniques of all kinds are covered here — from the simplest ones to more complex bending and carving.”
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.

We offer top quality woodcraft products. When it comes to quality, dedication and a commitment to excellence we can't be beat! We have a large selection of online craft supplies for the hobbyist or the professional woodcrafter. We're dedicated to meet your craft and woodcraft products needs. Check out our online store and let us help you make your next woodcraft projects shine!
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
As a tribute to Tage Frid who passed away in 2004, combined with the 30th anniversary of The Taunton Press, this three-volume slipcase set is the most complete, authoritative guide to woodworking for readers of all skill levels. The books in the slipcase include: “”Book 1: Joinery,”” “”Book 2: Shaping, Veneering, Finishing,”” and “”Book 3: Furnituremaking,”” The techniques illustrated in these books are demonstrated step by step, with clarity and organization that allows readers to understand and carry out virtually any woodworking project.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.

One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.

×