The wide variety of landmark furniture pieces, no matter the style, is what makes this book so visually stunning. That, and the fact that all of the 84 pieces that comprise the collection are beautifully photographed and a short description about each maker and piece is included. Many of the great makers from the last 100 years are covered – Sam Maloof, Wendell Castle, Tage Frid, George Nakashima – as well as many lesser known makers. If you read this book one hundred years from now, I’m sure it would be as thought provoking as it is today. These are 84 great pieces, and this is one great book.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
The Complete Manual of Woodworking A comprehensive book that covers tons of woodworking topics: woodworking design, hand tools, power tools, workshops, wood carving, joinery, finishing wood. You will also learn a lot about this natural resource we call wood. Filled with great photos, diagrams, and illustrations. If you want to branch out and explore other woodworking endeavors, you will enjoy owning this book.
I just got this book a few days ago, and I've had a hard time putting it down. There are lots of full-color pictures, with thorough descriptions of almost every aspect of woodworking. I've already learned a lot about different types of wood, how to make several kinds of cuts with several kinds of tools (including suggestions for what to do even though I don't have a large selection of power tools), and have some projects picked out to start as soon as I can get the lumber! It is a very thorough book, unlike several others I looked through at my local bookstore. I would highly recommend it to anyone who's interested in woodworking! It is both fun and informative. Almost half of this substantial book is general background information and instruction, including a detailed glossary, and the rest is a good selection of detailed, well-illustrated plans.
Furniture with Soul sheds light on some of the worlds most respected and revered makers of fine furniture. Going into their shops and learning how they got into the craft, what they most enjoy about it, and hearing some funny stories along they way is what this book is all about. It’s not a how-to in any way, unless you’re talking about how these selected group of makers made a living creating exquisite works of art. Beautiful photos of creative and challenging pieces of furniture are included throughout. My favourite book from the last year.
Woodworking books, plans and CDs allow you to study the methods of woodworking experts to reduce the learning curve on woodworking projects and save valuable time in the workshop. Reading a woodworking book is the easiest and least expensive way to learn from woodworking legends and craftsmen. Woodworking tips and lessons from masters like Tage Frid, Frank Klausz, Sam Maloof, Thomas Moser, Ian Norbury, Toshio Odate, Rude Oslnik, David Pye, and Gustav Stickley can be right at your finger tips. If your are interested in improving your hand tool skills or learning classic furniture-making techniques, we find Lost Art Press Books to be among the most important woodworking book collections we offer. With Christopher Schwarz as part of the writing and publishing team, you will be gaining access to one of the most creative and knowledgeable woodworkers around.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.
Proportion is the correlative relationship of all the parts to the whole. Although proportion usually refers to size, it is also a way to compare harmony between colour, quantity, placement and degree. Proportion is achieved when all sizes, shapes, textures, colors and so on complement one another. Remember that the eye appreciates some differences and may find equal parts monotonous and boring. Dividing space into equal parts such as halves, quarters and thirds is predictable and as a result the eye often skips past it.
This book is a solid book and much more than I would of imagined. I was thinking ok 40 plans cool. They go into detail on each plan. They give accurate measurements, pictures, times for each stage of a project, list of tools, wood, and anything else you need to complete each project. This book goes so far to even show you how to setup your own project and draft it and gives you a list of what you might need to draft out a project. I would say this book is good for anyone from Novice to Advanced. It is just a great read as well.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
Featuring each piece in highly-detailed, exploded drawings and applying time-honored dimensions and ergonomic standards, this comprehensive visual sourcebook takes the guesswork out of furniture joinery, assembly, dimension, and style. Woodworkers of any skill level will benefit from more than 1,300 crisp and detailed drawings that explain classic solutions to age-old problems, such as hanging a drawer, attaching a tabletop, and pegging a mortise.”
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
Geometric shapes are made from straight or curved lines such as circles, squares and triangles. Their easy-to-recognize and often symmetrical patterns offer a sense of order, efficiency, strength, formality, but to some may be seen as uninteresting. Squares and rectangles are the predominant geometric shapes seen around us, not only in furniture, but in all areas of life. A circle has no beginning or ending, making it complete and inspiring thoughts of nature, perfection, unity, initiation and inclusion.
Fast forward to adult me. I’m a full-blown city girl whose idea of crafting mostly consists of small handheld tasks (i.e. jewelry making, crocheting, colouring books, etc.). I’ve completely forgotten about how much woodworking was a part of my childhood and how beautiful the work of it can be. Then NBC came out with what (in my humble opinion) is one of the greatest television shows ever created. Making It is a traditional competition style reality show that showcases the work of different crafts people from around the United States. They specialize in everything from paper crafting to (you guessed it) woodworking. Oh and it’s hosted by these two fabulous goofballs.
The Workshop Book: A Craftsman's Guide to Making the Most of Any Work Space by Scott Landis. This is not a new book - it was written in 1987. And the photographs reflect that. But what it lacks in that flip-through-the-pictures-and-get-major-workspace-envy, it makes up for in the actual text. It provides, mostly, creative solutions for a variety of different tasks from real professionals working in limited space. If you're interested in upgrading your space or building your dream shop from scratch, this really is a good place to start. It doesn't have a ton of up-to-date and practical advice; its more of a reflection on the nature of workshops in all their variety. And that never goes out of style.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.