With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Audubon Birdhouse Book: Building, Placing, and Maintaining Great Homes for Great Birds Not only does this book offer great instructions and pictures on building birdhouses, but it also teaches you what makes for a safe and successful birdhouse for our little feathered friends. Lots of tips on where to place birdhouses and how to maintain them. This book is very much focused on the bird enthusiast and not so much the aesthetics of birdhouses.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Finishing is often an afterthought and spraying a finish isn’t exactly the first technique discussed when the topic does come up. While it’s often easier to wipe on a couple of coats of finish and be done with it, there are times when spraying a finish makes the most sense. There are many advantages to spraying a finish but there are some drawbacks too. Spray Finishing Made Simple does what it claims – it takes an imposing, unfamiliar topic and makes sense of it. This book is for the first-time spray finisher, as it starts with the basics and progresses through the stages. Don’t let the unknown stand in your way if you’re interested in learning about spraying. Pick up this book and get spraying.
As I was handling the 2x4's, during the routing, I realized that I really wouldn't be happy with the look of the bench, if it were made from these unfinished boards. They had stamps, pencil marks, and more importantly, incipient splinters left by the saw, none of which I wanted. And I was remembering what other shop furniture made from unfinished pine had looked like, after a few years in the grime of a shop.
Of all the machines in a workshop, we think two deserve their own books, not just because they possess the greatest potential, but when used incorrectly, are most likely to bite back. Bill Hylton and Fred Matlack’s Woodworking with the Router comes close to being the Router Bible. This tome provides an excellent overview of routers and bits while also explaining how to build and use jigs for router tables and handheld routing. Similarly, Paul Anthony’s Complete Illustrated Guide to Tablesaws gives entry-level and experienced woodworkers the information they need to safely use this workshop workhorse and accomplish more with their saws. Both books have excellent photos and great illustrations.
I will admit, I'm not a pyrography genius. In fact the last time used a woodburning tool, it was Christmas Day and was about five years old. It didn’t go well. A lot has changed since then. The tools have improved, there is a large and growing group of woodburning artists and there are great books to show you the basics and inspire you to pick up the art of pyrography. Woodburning with Style is the perfect book if you’re just learning. Not only will it teach you about the equipment available, it covers decorative techniques, lettering, portraits and more, before providing a chapter of inspirational projects and photographs to really get your imagination going. Pyrography is an art in itself but can also be used in conjunction with turnings, carvings or furniture making.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
David Ellsworth has been refining his style for years and now, with his first book, you get to see exactly how the “grandfather” of turning does it. Offering more than just turning information, a number of chapters in this book discuss topics that non-turners will be interested in. Having said that, turning is the main focus here. Ellsworth speaks to what he knows best – an open bowl, a natural-edge bowl and the highlight of the book, a hollow vessel with an impossibly small opening. He also covers basics like sharpening, design, finishing and more. One chapter even details the stresses that turning puts on the human body and how to get the most from this overlooked “tool”. A crucial read for a wood-turner and an enlightening read for a woodworker.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
If you’re looking for fresh, simple projects that have a rustic touch to them, this is the book for you. Lubkemann has a way of finding a project in just about every part of a tree; from candle-holders, photo frames and salt shakers to coat trees, lamps and a checkers set, there are projects big and small. Whether you’re looking for some gift ideas or you want the odd project to keep you busy over the winter, I’m sure you will find something here.
Comprehensive is the only word to describe this three-book set on joinery, shaping wood and furniture and cabinet construction. The three authors answer questions you didn’t even know you had. They also do it in a clear, concise and visually pleasing way. Even beginning to list the topics covered would be futile. Safe to say, if you want to learn about something that would fit under these three headings, this set will steer you in the right direction. Each book starts out with the basics and builds on that information, finishing off with quite advanced techniques.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.