The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.
The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Woodworking Basics presents an approach to learning woodworking that has proven successful for hundreds of people who have taken the author’s introductory course over the past 20 years. Peter Korn’s method helps new woodworkers learn the right techniques from the beginning.More experienced woodworkers can use it to master the classic furniture-making skills key to fine craftsmanship. Korn includes two attractive and useful projects — a small bench and a side table with a door and drawer — providing you the opportunity to practice skills and develop confidence with tools.
So drill the benchdog holes through the MDF layer. Begin by laying out their positions. You'll want these to be precise, so that the distances between the holes are consistent. The vises you are using will constrain your benchdog spacing. My front vise worked most naturally with two rows of holes four inches apart, my end vise with two pairs of rows, with four inches between the rows and eight inches between the pairs. Because of this, I decided on a 4" by 4" pattern.
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
Fast forward to adult me. I’m a full-blown city girl whose idea of crafting mostly consists of small handheld tasks (i.e. jewelry making, crocheting, colouring books, etc.). I’ve completely forgotten about how much woodworking was a part of my childhood and how beautiful the work of it can be. Then NBC came out with what (in my humble opinion) is one of the greatest television shows ever created. Making It is a traditional competition style reality show that showcases the work of different crafts people from around the United States. They specialize in everything from paper crafting to (you guessed it) woodworking. Oh and it’s hosted by these two fabulous goofballs.
As a teacher I find Ernest Joyce’s “The Technique of Furniture Making” (Batson) invaluable, ’tho it is as far away from an enjoyable read as possible. Similarly Bob Wearing’s “Essential Woodworker” (Lost Art Press). Bob is one of the only people who ever gave insight into traditional English technique. I believe the lack of similar books is due to the apprenticeship tradition of teaching, where nothing was ever written down.
Penland School of Crafts has been operating in the foothills of the Blue Ridge Mountains for over 75 years. This book details how ten instructors – all experts in their fields – make some of the furniture for which they are best known. Each instructor is vastly different from the next, and the tips they detail are highly innovative yet understandable and useful to the amateur woodworker. The director of the school, Jean McLaughlin, says the aim of the book is threefold. “To give the reader insight into the creative and technical processes of leading woodworkers, to provide detailed, intermediate-level technical information, and to showcase a range of approaches to the material.” The book excels on all three levels. Even when Istrongly disliked the style of furniture being discussed, revelled in the unique approach the maker took to break new ground to complete the finished piece. If you would like to see how one-of-a-kind pieces of studio furniture are made, and start to add some new techniques to your arsenal, either take a trip to North Carolina or pick up this book.
Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
Renewing Your Subscription: If you are ordering as a renewal to the same name and address as the current subscription, the publisher will add the Amazon order to your current subscription. For example, if you have 5 issues left and you add 12 through Amazon, you will now have 17 issues left on your subscription. Please note that the expiration date in the Magazine Subscription Manager will not reflect if you were already on file with the publisher. We will work with the publisher to ensure that you still receive all of the issues left on your subscription.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Cabinetmaking at the highest level is an art, a discipline, a philosophy–even a way of life–in addition to being a useful craft. In this book one of the greatest living cabinetmakers reflects on the deeper meanings of his craft and explains for less accomplished workers how the right attitudes toward materials, tools, and time can increase the joys of this complex activity. Craftspeople in every medium will be inspired by this account of getting started and developing habits that lessen the difficulties of a complex craft.
Ok, I’ve had my morning coffee and now it’s about time to get out to the shop to see what I can do to make that bench a little more pleasing to my eye. I like that Craftsman flair idea. That was my intent at the time I built it, too bad I got lazy and rushed the job. It’s not like I was going to make hundreds of benches for someone else and would never see it again. I should have taken the time to make it the way I wanted it to look. This could keep me entertained for awhile. I see major surgery in the forecast! Gotta plan it all out just right.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Grizzly is a company currently undergoing an upheaval. This brand was once known as a manufacturer of professional grade tools and equipment for woodworking products. Though, in recent years, that reputation has begun to slip a bit since being bought by the Chinese company SIEG. These days, whether the Grizzly product stands up to its previous standards of excellence often has more to do with what you are buying than the company itself.