Over 1,400 color photos and drawings illustrate the methods, from simple butt joints to angled tenons and complex scarf joints. A project as simple as a box, for example, has a dozen ways to solve the joinery question. And, since many joints can be used interchangeably, Joinery leads you through making the right choice for your project based on the function of the piece, the time you have to work on it, your skill level, and your tooling.
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
This book is a solid book and much more than I would of imagined. I was thinking ok 40 plans cool. They go into detail on each plan. They give accurate measurements, pictures, times for each stage of a project, list of tools, wood, and anything else you need to complete each project. This book goes so far to even show you how to setup your own project and draft it and gives you a list of what you might need to draft out a project. I would say this book is good for anyone from Novice to Advanced. It is just a great read as well.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.

Audubon Birdhouse Book: Building, Placing, and Maintaining Great Homes for Great Birds Not only does this book offer great instructions and pictures on building birdhouses, but it also teaches you what makes for a safe and successful birdhouse for our little feathered friends. Lots of tips on where to place birdhouses and how to maintain them. This book is very much focused on the bird enthusiast and not so much the aesthetics of birdhouses.
Pattern is the ordered repetition of an individual element. Pattern needs repetition in order to be considered a pattern. However, as already mentioned elsewhere, repetition can become boring. Slight variations in a pattern break monotony and add life to it. This also makes a pattern more familiar, especially if it relates closely to patterns found in nature. If a pattern is being created using a decorative motif, consider the dimensions of the surface area on which the motif will be seen to determine the motif’s scale. Larger surfaces can support a larger motif and allow the viewer to fully appreciate the impact of the repetition. If the motif is too small, it can be distracting and make the area feel busy.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
×