Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Contrast is created when you have two or more related elements that are different. Contrast can be used to add visual interest, depth and to highlight a dominant element. It is also a way to unite a piece and often bestows energy to a design. If there are too many contrasts or the differences are too severe, there is risk they will not only compete for attention, but may also create unbalance, confuse the viewer and create optical illusions. To achieve success with contrast, ensure the differences are obvious enough, but without an overpowering presence. Each design element mentioned in this article can be manipulated to create contrast. Each of the images not only relate to the corresponding element but also exhibit contrast.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
The hits included Shop Tips, Woodworking: The Right Technique, Router Magic, Woodworker’s Problem Solver and the Woodworker’s Visual Handbook. Each of those books sold more than 100,000 copies because of the quality of the advice and projects. And the books still hold up well, as you can see if you view buyers’ comments on sites like Amazon, where most of the titles consistently receive 5-star ratings.
For those who would like to have the benefit of a woodworker’s extensive experience with hand tools, this is the book to own. Crammed with practical information, it is the next best thing to looking over a craftsman’s shoulder as he works with his tools, asking questions and getting straight answers in plain language, seeing how each tool is held and manipulated to get the best work out of it. From bit brace, chisel, and mallet to saws, specialized planes, drawknife, and spokeshave, Aldren Watson describes in detail the actions of the tools basic to good woodworking. All the procedures are explicitly illustrated with handsome line drawings, and an appendix gives plans and dimensions for making a workbench and other necessary pieces of shop equipment.”
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
There are two books that I would consider highly influential in my personal woodworking path. Darrell Peart’s “Greene & Greene: Design Elements for the Workshop” (Linden) and “Adventures in Wood Finishing” by George Frank (Taunton). Peart’s book kicked off my fascination with all things Greene & Greene. Peart does a fantastic job of covering history as well as practical techniques.
I find furniture takes on new meaning when separated from the sterility of an art museum (such as the Philadelphia Museum of Art’s American Wing. Maybe that’s why I prefer the museum’s period rooms). Jeffrey P. Greene’s book is perhaps my favorite of recent period woodworking texts for its ambition and helpful exploded diagrams of furniture in its appendix.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
This table top is also made from the hardest wood out of any manufacturer we reviewed: oak. In fairness, this can be both a blessing and a curse. The oak wood is extremely durable and noted for its lack of a porous nature. This means the top can withstand plenty of abuse from tool and workpieces. Moreover, you will not have to worry about liquids like lacquers and stains from being absorbed into the top. That said, the hard oak can also do a number on tool sharpness, dulling them prematurely if they are not carefully handled.