Comprehensive is the only word to describe this three-book set on joinery, shaping wood and furniture and cabinet construction. The three authors answer questions you didn’t even know you had. They also do it in a clear, concise and visually pleasing way. Even beginning to list the topics covered would be futile. Safe to say, if you want to learn about something that would fit under these three headings, this set will steer you in the right direction. Each book starts out with the basics and builds on that information, finishing off with quite advanced techniques.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
I marked out the one hole location, drilled a shallow 1/16" hole into the top. I then put a 1/16" bit through the hole in my template and into the hole I had just drilled. I lined up the template, and drilled a second hole, then put another bit through that. From then on, I worked entirely from the template. With two bits through the holes pinning the template in place, the other holes in the template would be precisely located (or so the theory goes) on a 4x4" grid.
This is a beautiful and inspiring book for anyone who wants to broaden their horizons when it comes to turning. Not a how-to book, it talks with over 30 world-renowned turners about their approach to the craft, and what keeps them motivated to push the boundaries and create exquisite pieces of art. You will learn more about the makers’ vision than how they produced their stunning works of art. I read every word of this book and studied every single photograph, and was completely enthralled the entire time. And I’m not even a turner! This book is for anyone serious about turning, or woodworking in general.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
Pyrography Workbook: A Complete Guide to the Art of Woodburning. It’s amazing what you can create with woodburning. You can make art that stands on its own, or use woodburning to personalize your crafts. In her book, Sue Walters talks about equipment, techniques, and safety. She also takes you step-by-step through 3 different projects for the beginner, intermediate, and the advanced woodburner. When I bought my first wood burner, I automatically purchased this book as well.
A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
Over 1,400 color photos and drawings illustrate the methods, from simple butt joints to angled tenons and complex scarf joints. A project as simple as a box, for example, has a dozen ways to solve the joinery question. And, since many joints can be used interchangeably, Joinery leads you through making the right choice for your project based on the function of the piece, the time you have to work on it, your skill level, and your tooling.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
When you have the other leg seated, the threaded rods will extend father than you want them to. You'll want to mark them so they can be cut to length. Place a washer and a nut on each threaded rod, and then tighten down the nut to pull everything tight. Depending upon the wrench you are using, and how much longer the rod is than it needs to be, you may find it necessary to stack up a number of washers, so that the nut is positioned where the wrench can operate on it.
With more than 1,800 drawings, diagrams and photos, this authoritative guide encompasses the whole art and craft of woodworking. Designed to instruct and inspire every woodworker from the beginner to the most exacting expert, it has become a classic. It includes a discussion of all the principal hardwoods and softwoods, how to choose and use hand tools, detailed information on every woodworking technique–jointing, bonding, fastening, laminating, and much more.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
The wide variety of landmark furniture pieces, no matter the style, is what makes this book so visually stunning. That, and the fact that all of the 84 pieces that comprise the collection are beautifully photographed and a short description about each maker and piece is included. Many of the great makers from the last 100 years are covered – Sam Maloof, Wendell Castle, Tage Frid, George Nakashima – as well as many lesser known makers. If you read this book one hundred years from now, I’m sure it would be as thought provoking as it is today. These are 84 great pieces, and this is one great book.
The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-standard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a collection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting something different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
I will admit, I'm not a pyrography genius. In fact the last time used a woodburning tool, it was Christmas Day and was about five years old. It didn’t go well. A lot has changed since then. The tools have improved, there is a large and growing group of woodburning artists and there are great books to show you the basics and inspire you to pick up the art of pyrography. Woodburning with Style is the perfect book if you’re just learning. Not only will it teach you about the equipment available, it covers decorative techniques, lettering, portraits and more, before providing a chapter of inspirational projects and photographs to really get your imagination going. Pyrography is an art in itself but can also be used in conjunction with turnings, carvings or furniture making.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
The Real Wood Bible I love to pull this book off my shelf from time to time and learn about different characteristics of a certain wood. What’s the wood used for? How easy is it to turn? Toxicity? It’s a very useful book with lots of great photos. Let’s say you have a piece of wood you need to identify. The photos are very crisp and defined so you can match a wood you possess to one found in the book.
Pattern is the ordered repetition of an individual element. Pattern needs repetition in order to be considered a pattern. However, as already mentioned elsewhere, repetition can become boring. Slight variations in a pattern break monotony and add life to it. This also makes a pattern more familiar, especially if it relates closely to patterns found in nature. If a pattern is being created using a decorative motif, consider the dimensions of the surface area on which the motif will be seen to determine the motif’s scale. Larger surfaces can support a larger motif and allow the viewer to fully appreciate the impact of the repetition. If the motif is too small, it can be distracting and make the area feel busy.
efore you cut your first board, you must have a design to achieve the results you're after. To create a workable design, you must understand important properties of the wood you will be using, methods for joining that wood, typical construction techniques that are appropriate for the type of project you are building, styles of craftsmanship that will enhance and compliment the environment where this project will be used, and finally how to think through and plan a project.
Chan’s desire for strong, lasting, easily repeated joints using power tools makes for a fun and educational read. He also has a strong interest in traditional Chinese furniture, and shows how some of those joints can be cut with power tools. This book will not only teach you how to machine about 100 useful joints, but will also open your eyes to using new, fun to make joints in upcoming projects. Chan assumes readers know how to use their machinery and power tools, so he focuses on the procedures required to produce the included joints.
New information on composite materials, adhesives, and finishes brings this book into the 21st century, while more than 300 photographs bring important visual information to life. This edition covers the nature of wood and its properties, the basics of wood technology, and the woodworker’s raw materials. Understanding Wood was written for woodworkers by a scientist with a love of woodworking. It will be sought after by craftsmen and collectors alike.”
Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
There are simple jigs like a trammel baseplate and T-square, but you’ll also find a vacuum-clamping jig you can use to rout surfaces without clamps getting in the way, a dowel-making fixture, and router jigs to help you make fluted columns and even flamed finials. Bill also included several variations of router tables, including an ultimate table I built for my own shop.
The next day, cut it flush. Use a block plane to ensure it truly is flush. This will be the top of the bottom layer of the bench top, so gouges aren't a problem. (Wiping up glue with a damp cloth can lead to stains and finishes applying unevenly. That won't be a problem here, either.) But bulges and bumps are a problem - they will keep the two layers of the top from matching up evenly.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.