If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.

Woodworking Basics presents an approach to learning woodworking that has proven successful for hundreds of people who have taken the author’s introductory course over the past 20 years. Peter Korn’s method helps new woodworkers learn the right techniques from the beginning.More experienced woodworkers can use it to master the classic furniture-making skills key to fine craftsmanship. Korn includes two attractive and useful projects — a small bench and a side table with a door and drawer — providing you the opportunity to practice skills and develop confidence with tools.


A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.

Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)


If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.
“Introducing a new woodworking series in the tradition of Tage Frid…a series filled with essential information required by woodworkers today. For the first time ever, all the techniques and processes necessary to craft beautiful things from wood have been compiled into three comprehensive volumes: The Complete Illustrated Guides. Highly visual and written by woodworking’s finest craftsmen, these three titles — Furniture & Cabinet Construction, Shaping Wood, and Joinery — will establish a new standard for shop reference books.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here

The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.
We will charge the payment method listed in Magazine Subscription Manager. If we cannot successfully charge this payment method, we will use the payment method you gave us when you originally placed your order. If we cannot successfully charge that payment method, we'll use another payment method you have saved in your Amazon.com account. Your initial sign-up is an authorization for us to use the preferred or other available payment methods to pay for your subscription.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
So drill the benchdog holes through the MDF layer. Begin by laying out their positions. You'll want these to be precise, so that the distances between the holes are consistent. The vises you are using will constrain your benchdog spacing. My front vise worked most naturally with two rows of holes four inches apart, my end vise with two pairs of rows, with four inches between the rows and eight inches between the pairs. Because of this, I decided on a 4" by 4" pattern.
With more than 30,000 high-quality products at competitive prices, we’re here to help make managing your farm, business or home easier and more efficient. FarmTek offers ClearSpan Fabric Structures and Greenhouses, livestock housing, feeders and drinkers, heaters, ventilation supplies, lighting, barn curtain, fencing, hoop barns, radiant heating supplies, equine supplies, insulation, high tunnels and cold frames, and more. Request your free catalog today!
Cabinetmaking at the highest level is an art, a discipline, a philosophy–even a way of life–in addition to being a useful craft. In this book one of the greatest living cabinetmakers reflects on the deeper meanings of his craft and explains for less accomplished workers how the right attitudes toward materials, tools, and time can increase the joys of this complex activity. Craftspeople in every medium will be inspired by this account of getting started and developing habits that lessen the difficulties of a complex craft.

The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-stan­dard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a col­lection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting some­thing different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
As a tribute to Tage Frid who passed away in 2004, combined with the 30th anniversary of The Taunton Press, this three-volume slipcase set is the most complete, authoritative guide to woodworking for readers of all skill levels. The books in the slipcase include: “”Book 1: Joinery,”” “”Book 2: Shaping, Veneering, Finishing,”” and “”Book 3: Furnituremaking,”” The techniques illustrated in these books are demonstrated step by step, with clarity and organization that allows readers to understand and carry out virtually any woodworking project.

Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.

Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.


The good news is that you don’t need a lot of shelf space to house a comprehensive collection of basic woodworking knowledge. Get started with Understanding Wood. In this comprehensive bible, professor Bruce Hoadley delves into the nature of wood and how its structure affects strength, workability, and other characteristics. He then shines a light on fundamentals like drying, machining, bending, joining, sanding, gluing, often accompanied by stunning macro photographs that zoom you in to the meat of the matter.
The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Put the countertop on the base, put the MDF on top of the countertop, and line up the marks you drew on each end of the MDF with the countertop below it. When you have it lined up, clamp things down, and route the edge of the MDF using a 1-1/2" or longer flush-trim bit, with the depth adjusted so the bearing rides on the countertop. I clamped a couple of scraps of doubled MDF at each end to give the router base something extra to ride on at the ends.

Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
×