My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
Woodworkers like books. Maybe it’s because they’re somehow still a wood product, but let’s face it, they travel into the shop well, offer great how-to instruction with pictures and words, and you can make notes in the margins if you like. Our fine woodworking books cover all the topics for which you’re looking: furniture plans; hand tool techniques; shop projects; wood finishing advice and much more.
Projects to build on. Korn's book includes basic projects that you can put your own spin on. This Shaker footstool was inspired by one of the projects in his book. The last side-table project in his book (pictured) has the same pedigree as these two other FW projects: Tim Rousseau's small cherry cabinet and Stephen Hammer's small stand with coopered panels.
For an entertaining read (and proof that woodworkers lead interesting lives), treat yourself to Nancy Hiller’s Making Things Work: Tales from a Cabinetmaker’s Life, and George Frank’s Adventures in Wood Finishing. These two biographical books are beautifully written and offer similarly lively accounts of the adventures that come from making a living as a woodworker. As you spend time with Nancy and George, we think you’ll enjoy the stories that come with the sawdust
The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-standard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a collection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting something different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.