While our website has the most comprehensive list of all of our tools, sometimes it's nice to flip through the pages of a good old fashioned catalog.  This contains only our most popular permanent products that we manufacture just outside of Cleveland, OH.  We will be happy to send you one at no charge.  Just click the order button below so we can get the address you would like it sent to.  

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
I just got this book a few days ago, and I've had a hard time putting it down. There are lots of full-color pictures, with thorough descriptions of almost every aspect of woodworking. I've already learned a lot about different types of wood, how to make several kinds of cuts with several kinds of tools (including suggestions for what to do even though I don't have a large selection of power tools), and have some projects picked out to start as soon as I can get the lumber! It is a very thorough book, unlike several others I looked through at my local bookstore. I would highly recommend it to anyone who's interested in woodworking! It is both fun and informative. Almost half of this substantial book is general background information and instruction, including a detailed glossary, and the rest is a good selection of detailed, well-illustrated plans.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
I know, if you had a workbench, you wouldn't be building a workbench. Even so, you'll need some sort of work surface, even if it isn't as stable or capable as a proper bench. The traditional solution is to throw a hollow-core door over a couple of saw horses. The advantage of hollow core doors is that they're flat, stiff, and cheap. I used a folding table and a hollow core door I had bought for a future project.

A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
Before you start cutting or drilling the pieces that will make up the top, determine the layout of the top. This should include the dimensions of the MDF, the dimensions of the edging, the locations of the vises, and of the screws or bolts that will support the vises, and of all of the benchdog holes and of all of the drywall screws you will use to laminate the panels,
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
Remember those fire safety tips you used to get in grade school, about the dangers of oily rags? It was linseed oil they were talking about. All oily rags are dangerously flammable. Linseed oil will self-combust. Linseed oil doesn't evaporate, it oxidizes. The oxidization generates heat, and the increased temperature increases the rate of oxidation.

The Handbuilt Home. Ana White has created a wonderful DIY book. It’s filled with 34 projects she describes as simple, stylish, and budget-friendly. And you’ve probably already guest that they are related to improving your home. Each project has diagrams and instructions. And she tells the level of difficulty and project costs. This book resonates with many readers who want to make things themselves, but they may not have the fancy tools or the budget. Ana shows you how to make beautiful and affordable DIY projects.


A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.

Furniture with Soul sheds light on some of the worlds most re­spected and revered makers of fine furni­ture. Going into their shops and learning how they got into the craft, what they most enjoy about it, and hearing some funny stories along they way is what this book is all about. It’s not a how-to in any way, unless you’re talking about how these selected group of makers made a living creating exquisite works of art. Beautiful photos of creative and challenging piec­es of furniture are included throughout. My favourite book from the last year.

This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
Stop it. Really. I mean it. Pick a height between your thigh and waist that seems right. You’ll adapt. Don’t worry about your back. You’ll adapt. If you are really uncertain, make it a little taller and then cut down the legs. After a decade or so, your work habits will put a magic number in your head. You’ll have built enough furniture that you will know your number. Until then, pick a number.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
“The Complete Guide to Woodworking features detailed plans for 40 stunning projects for woodworkers of all levels, plus more than 1,200 step-by-step illustrations. It also includes expert information on setting up a workshop, safety, how to use and look after tools, and much more. For beginners and experienced woodworkers alike, this is the ultimate step-by-step guide.
Beyond the weight capacity, the Grizzly is also the largest table top on our list and in more ways than one. For a workspace, the Grizzly provides 5’ of length by 2 ½’ of width. There is not another table that really comes close to that size. Another size advantage of the Grizzly bench is the table top’s thickness. While the standard thickness of the table top for a quality woodworking bench is 1” with lesser models often offering only ¾” of thickness, the Grizzly provides a 1 ½” thick table top.
×