Another aspect that might irk some buyers is the fact that the capacity of this bench is less than great outside of weight. The top’s surface area is a bit on the smaller end, though its length is more in line with larger models. The width though is less than two feet which can limit some projects. Similarly, the vice capacity is the second smallest on our list at 4 ½”, though this too can be modded with optional additions.
Projects to build on. Korn's book includes basic projects that you can put your own spin on. This Shaker footstool was inspired by one of the projects in his book. The last side-table project in his book (pictured) has the same pedigree as these two other FW projects: Tim Rousseau's small cherry cabinet and Stephen Hammer's small stand with coopered panels.
So since more than half the book is taken up with instruction, I thought there wouldn't be enough room for 40 projects. Thing is, the projects are mostly VERY simple and functional. There really does not seem to be any sort of eye towards craftsmanship and design. And they are almost all ugly. The picture frames included are literally the ugliest I've ever seen. Obviously, style is in the eye of the beholder, but I can't be making furniture to go in my home that looks like that, and my home is Ikea, Crate and Barrel, and Bombay to give you an idea.
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
Tapping the knowledge of dozens of top-shelf woodworkers, Scott Landis’s The Workbench Book, and Jim Tolpin’s The Toolbox Book are filled with inspirational photos and drawings that you can use to enhance your workbench and tool storage needs. John White’s Care and Repair of Shop Machines completes the workshop triumvirate. The author’s straightforward advice for repairing and setting machinery will help you make the most of every machine in your shop.
Texture is the surface quality of a material. Texture has great potential to connect the observer emotionally to the work, inviting the person to touch and explore it. On a chair, for example, the texture of fabric can tempt persons to sit in it or immediately reject it. Smooth surfaces reflect light and can appear shiny making a piece feel light. Heavily textured surfaces absorb light. When considering texture, look at it from all angles and under different light conditions to see the full impact of its surface. To help determine scale with texture, the guidelines under pattern and proportion can also be followed.
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.