4. Taunton's Complete Illustrated Guide To Finishing by Jeff Jewitt. This isn't the only book on the subject, but it's a great place to start. The real strength here is the bounty of color photos, which show exactly what's happening as you finalize your projects. It discusses finishing new projects, but also repairing old finishes and matching vintage pieces. It's not a "start here, end there" walk through, so you'll need to familiarize yourself with the way it's organized before beginning a project, but it is indeed a "complete illustrated guide" with encyclopedic-like thoroughness. Belongs in every library.
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
As I try to improve as a woodworker and artist, I really want every piece to be better than my last. But this piece will always hold a special place in my ❤️ This table is made of 1250+ pieces of recycled skateboards and walnut, but If you count the individual veneers of the recycled skateboard pieces then it’s made of over 6,800 pieces of wood. 📷 @fvcksandflamingos 😘 #upcycledskateart
Of all the machines in a workshop, we think two deserve their own books, not just because they possess the greatest potential, but when used incorrectly, are most likely to bite back. Bill Hylton and Fred Matlack’s Woodworking with the Router comes close to being the Router Bible. This tome provides an excellent overview of routers and bits while also explaining how to build and use jigs for router tables and handheld routing. Similarly, Paul Anthony’s Complete Illustrated Guide to Tablesaws gives entry-level and experienced woodworkers the information they need to safely use this workshop workhorse and accomplish more with their saws. Both books have excellent photos and great illustrations.
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.
The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-standard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a collection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting something different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.
This is, as the title states, a book that details some incredibly advanced veneering techniques. If you have a solid foundation in basic veneering, and want to see what else can be done with this wonderful medium, this book will have you laying out veneer in ways you’ve never previously dreamt of. It will also have you asking yourself what else is possible. The extremely detailed step-by-step photos keep you visually onside with what Grove is doing, as words (as clear and concise as they are) are not enough.
The Workshop Book: A Craftsman's Guide to Making the Most of Any Work Space by Scott Landis. This is not a new book - it was written in 1987. And the photographs reflect that. But what it lacks in that flip-through-the-pictures-and-get-major-workspace-envy, it makes up for in the actual text. It provides, mostly, creative solutions for a variety of different tasks from real professionals working in limited space. If you're interested in upgrading your space or building your dream shop from scratch, this really is a good place to start. It doesn't have a ton of up-to-date and practical advice; its more of a reflection on the nature of workshops in all their variety. And that never goes out of style.
The person who coined the saying, “The more things change, the more they stay the same,” just might have been a woodworker. Admittedly, new tools and materials have made certain operations faster, safer, and easier, but if a woodworker from the 1900s could visit your workshop, he’d have a tougher time with the K-cup coffeemaker than the table saw. That’s because the basic tenets and tools of woodworking are almost timeless.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
I was raised by crafty people. In every sense of the word. Just kidding! My parents were lovely people who loved to work with their hands in their spare time. For a brief period of time as a kid my mom even earned a living by selling her wares at local craft fairs, but for the most part their crafting was a hobby that filled our home with beautiful and practical pieces of woodworking.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Chan’s desire for strong, lasting, easily repeated joints using power tools makes for a fun and educational read. He also has a strong interest in traditional Chinese furniture, and shows how some of those joints can be cut with power tools. This book will not only teach you how to machine about 100 useful joints, but will also open your eyes to using new, fun to make joints in upcoming projects. Chan assumes readers know how to use their machinery and power tools, so he focuses on the procedures required to produce the included joints.
This is a beautiful and inspiring book for anyone who wants to broaden their horizons when it comes to turning. Not a how-to book, it talks with over 30 world-renowned turners about their approach to the craft, and what keeps them motivated to push the boundaries and create exquisite pieces of art. You will learn more about the makers’ vision than how they produced their stunning works of art. I read every word of this book and studied every single photograph, and was completely enthralled the entire time. And I’m not even a turner! This book is for anyone serious about turning, or woodworking in general.
“Introducing a new woodworking series in the tradition of Tage Frid…a series filled with essential information required by woodworkers today. For the first time ever, all the techniques and processes necessary to craft beautiful things from wood have been compiled into three comprehensive volumes: The Complete Illustrated Guides. Highly visual and written by woodworking’s finest craftsmen, these three titles — Furniture & Cabinet Construction, Shaping Wood, and Joinery — will establish a new standard for shop reference books.
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
So drill the benchdog holes through the MDF layer. Begin by laying out their positions. You'll want these to be precise, so that the distances between the holes are consistent. The vises you are using will constrain your benchdog spacing. My front vise worked most naturally with two rows of holes four inches apart, my end vise with two pairs of rows, with four inches between the rows and eight inches between the pairs. Because of this, I decided on a 4" by 4" pattern.
If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
My woodworking mentor, Robert Van Norman, studied under the esteemed woodworker James Krenov. Robert remembers many of JK’s wise words, especially “trust your eye”. When it was time for me to hear those words, I remember feeling such relief and permission to embrace my inherent perspicacity. Intuition is essential in the design and creation process, and for developing work that reflects the maker beyond his or her technical skill alone. At times, the craftsperson is called on to explain the aesthetics of his design and saying “it just feels right” doesn’t always cut it. This article covers seven common design considerations, their definition and how they are generally accepted and understood. Not only will the article help increase design vocabulary and awareness, but it may also assist in problem solving and recognizing the aesthetic strengths and weaknesses of a furniture piece.
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.
Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
For the most part, furniture restorers/refinishers/conservators in the United States lack the necessary hand-tool skills to do proper wood repairs. But avid readers of Popular Woodworking Magazine do possess the skills. Like me in the 1970s, you just need instruction on how to go about it. These books provide this. They greatly influenced the techniques I use in my shop, and many are shown in the “Repairing Furniture” video/DVD I made for Taunton.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.