Woodworking books, plans and CDs allow you to study the methods of woodworking experts to reduce the learning curve on woodworking projects and save valuable time in the workshop. Reading a woodworking book is the easiest and least expensive way to learn from woodworking legends and craftsmen. Woodworking tips and lessons from masters like Tage Frid, Frank Klausz, Sam Maloof, Thomas Moser, Ian Norbury, Toshio Odate, Rude Oslnik, David Pye, and Gustav Stickley can be right at your finger tips. If your are interested in improving your hand tool skills or learning classic furniture-making techniques, we find Lost Art Press Books to be among the most important woodworking book collections we offer. With Christopher Schwarz as part of the writing and publishing team, you will be gaining access to one of the most creative and knowledgeable woodworkers around.
I know, if you had a workbench, you wouldn't be building a workbench. Even so, you'll need some sort of work surface, even if it isn't as stable or capable as a proper bench. The traditional solution is to throw a hollow-core door over a couple of saw horses. The advantage of hollow core doors is that they're flat, stiff, and cheap. I used a folding table and a hollow core door I had bought for a future project.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
Grouping George Nakashima’s The Soul of a Tree and Jim Krenov’s Worker in Wood with Nick Offerman’s Good Clean Fun might seem sacrilegious, but we like how the trio’s perspectives encompass the diverse spirit of woodworking. The older books combine photos of exceptional work with serious reflections on the nature of craftsmanship. Nick is equally passionate about wood and woodworking, but he’s more willing to admit that he’s enjoying himself–a good example for all of us to follow.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
I have picked out a list of 9 books on woodworking that covers a wide variety of woodworking hobbies and techniques. I can personally vouch for these books, since I own most of them. These books will serve as valuable reference tools that can be used over and over. I’ve also checked the ratings and comments to make sure these books resonate with their readers. For your convenience, I’ve also included Amazon affiliate links so you can check out the Amazon reviews yourselves. Hope you enjoy the article and towards the end, I will ask you to share your favorite woodworking books.
Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
The latest edition of this highly regarded instructional manual. See the great reader reviews posted for the previous editions. With this book and a weekend of your time you can make a plane and learn to use it effectively. You’ll also discover a wealth of general woodworking tips and acquire a solid grounding in many fundamentals of fine woodworking. Now in its third printing, “Making and Mastering Wood Planes” by master craftsman David Finck is the definitive book in the field and a classic introduction to the art of fine woodworking.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
Woodworking Business is an informative, common-sense-based book that may answer many questions for the amateur woodworker who is considering going professional. This is not a gorgeous book. It doesn’t have glossy photos or beautiful graphic design. What it does offer is practical, down-to-earth tips while forcing you to consider the toughest question of all: Is running your own business right for you? Chapter topics include Setting Prices, Contracting Jobs, Getting Help and Everyday Lessons. Although it’s written from an American perspective, most of the information is pertinent to a Canadian reader.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
Once you've placed an order at Amazon.com, it can take one to two weeks for your subscription to be received and scheduled by the publisher. Your subscription is then added to the publisher's next production cycle and shipped via standard mail. For example, if your monthly subscription was ordered and received by the publisher in November, and the December issue has already shipped, your order may be added to the January mailing. You can find out more information, including how to contact the publisher about your subscription, in Amazon's Magazine Subscription Manager.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
Pattern is the ordered repetition of an individual element. Pattern needs repetition in order to be considered a pattern. However, as already mentioned elsewhere, repetition can become boring. Slight variations in a pattern break monotony and add life to it. This also makes a pattern more familiar, especially if it relates closely to patterns found in nature. If a pattern is being created using a decorative motif, consider the dimensions of the surface area on which the motif will be seen to determine the motif’s scale. Larger surfaces can support a larger motif and allow the viewer to fully appreciate the impact of the repetition. If the motif is too small, it can be distracting and make the area feel busy.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
A bewildering variety of tools, clever marketing copy, and lack of knowledge can lead even the most determined new woodworker to make many unnecessary purchases, causing frustration or retreat. Written for true beginners, Your First Shop offers inspiration and encouragement, guiding readers toward smart tool choices by providing realistic, reliable information. Best-selling author Aimé Ontario Fraser started working with wood in high school, and has taught extensively in workshops and classes since. Your First Shop brings that experience to readers. Woodworkers of every taste can find a shop style that works for them in one of the book’s four sections: The Essential Shop, The Basic Shop, The Efficient Shop, and The Well-Rounded Shop. Topics include how each tool is used and what it is used for. The book also offers extensive advice on choosing a location for the shop, maximizing available space, and planning for future expansion.
Remember those fire safety tips you used to get in grade school, about the dangers of oily rags? It was linseed oil they were talking about. All oily rags are dangerously flammable. Linseed oil will self-combust. Linseed oil doesn't evaporate, it oxidizes. The oxidization generates heat, and the increased temperature increases the rate of oxidation.
I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
First, cut one long edge. Second, cut a short edge, making sure it's square to the long edge you just cut. Clamp both pieces of the edging you'll be using along the long edge you've cut, and measure the width of the base plus 1/4-1/2", mark that, and then lay out a line through the mark that is square to the end you've cut, then cut along the line. Finally, cut the remaining short edge square to both long edges. (The length of the top doesn't need to precisely match anything, so we don't need to bother with clamping the trim before measuring.)
I am new to woodworking. I'm learning as I go along, and I'm documenting as I learn, in the hope of being helpful to other novices. On the range from slap-dash to deliberate, my method is definitely on the deliberate side. If you have enough experience to be confident in using techniques that are more time-efficient, go for it. The techniques I'm using are those I thought least likely to go wrong, not those that would produce a product in the shortest time or at the lowest cost. You'll notice that I made a number of mistakes, spent considerable time on work I later determined to be unnecessary, and in a number of cases I used different techniques at the end than I did at the beginning. These are all the result of learning. I thought it would be better to demonstrate how I made errors, and how I corrected them, than to provide a set of instructions that presented the false impression that everything went together perfectly.
So since more than half the book is taken up with instruction, I thought there wouldn't be enough room for 40 projects. Thing is, the projects are mostly VERY simple and functional. There really does not seem to be any sort of eye towards craftsmanship and design. And they are almost all ugly. The picture frames included are literally the ugliest I've ever seen. Obviously, style is in the eye of the beholder, but I can't be making furniture to go in my home that looks like that, and my home is Ikea, Crate and Barrel, and Bombay to give you an idea.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…