As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
Time for Geometric Shapes – Neil Moledzki Tribute clock is a reproduction of a clock made by James Krenov. The sweeping curves and the impression we get of the clock weighing down the stand produces an organic and even animated feel to the piece. It should be noted that something that has an organic feel is not the same as having an organic shape. If we break the parts down on the clock, we can see it is made entirely of geometric shapes.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
You may even want to put yourself in the picture. If your workshop space already exists, find a large piece of cardboard, wallboard, or plywood that’s about the size of the workbench top you envision. Find a couple of stools or chairs, perhaps a few books, and turn them into stanchions to support the “benchtop.” Is it too big for the space? Is it large enough for the tasks you envision will be performed upon it?
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
The latest edition of this highly regarded instructional manual. See the great reader reviews posted for the previous editions. With this book and a weekend of your time you can make a plane and learn to use it effectively. You’ll also discover a wealth of general woodworking tips and acquire a solid grounding in many fundamentals of fine woodworking. Now in its third printing, “Making and Mastering Wood Planes” by master craftsman David Finck is the definitive book in the field and a classic introduction to the art of fine woodworking.
Being a lover of Japanese design and tools, I’m embarrassed to say I only picked this book up in the last year. I was anticipating a straightforward, almost encyclopaedic, approach documenting the history and use of most Japanese woodworking tools. I got that, but also so much more. The stories Odate tells of his youth and apprenticeship are truly jaw-dropping, and reveal as much about working wood in Japan as what life in a fascinating and secluded Pacific country was like when he was young. I was five minutes into this book, and I guess I had an astonished look on my face, when my wife politely asked how I was enjoying the book. I looked up in bewilderment, paused for about five seconds, and said “It would take me an hour to explain what I’ve learned in the last five minutes,” and went on reading. Even though this book has been around for decades, it’s worth reading today.
2 - use a plunge router with a bottom bearing cuter bit such as this from rockler: http://www.rockler.com/product.cfm?page=25160&site=ROCKLER .... I thought to use the short one as I plunge it directly downward in the centre of the hole until the bearing reaches within the tabletop hole. I suppose one could use a long one, but the stubbiness seemed more practical (the big bearing ensured accuracy?)
Grizzly is a company currently undergoing an upheaval. This brand was once known as a manufacturer of professional grade tools and equipment for woodworking products. Though, in recent years, that reputation has begun to slip a bit since being bought by the Chinese company SIEG. These days, whether the Grizzly product stands up to its previous standards of excellence often has more to do with what you are buying than the company itself.