This table top is also made from the hardest wood out of any manufacturer we reviewed: oak. In fairness, this can be both a blessing and a curse. The oak wood is extremely durable and noted for its lack of a porous nature. This means the top can withstand plenty of abuse from tool and workpieces. Moreover, you will not have to worry about liquids like lacquers and stains from being absorbed into the top. That said, the hard oak can also do a number on tool sharpness, dulling them prematurely if they are not carefully handled.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
Pattern is the ordered repetition of an individual element. Pattern needs repetition in order to be considered a pattern. However, as already mentioned elsewhere, repetition can become boring. Slight variations in a pattern break monotony and add life to it. This also makes a pattern more familiar, especially if it relates closely to patterns found in nature. If a pattern is being created using a decorative motif, consider the dimensions of the surface area on which the motif will be seen to determine the motif’s scale. Larger surfaces can support a larger motif and allow the viewer to fully appreciate the impact of the repetition. If the motif is too small, it can be distracting and make the area feel busy.
Shape is critical to the ultimate success or failure of a piece of furniture. Knowing this, custom-furniture maker Lonnie Bird has taken the complex subject of shaping and in this book made it accessible to every woodworker. He guides the reader toward first visualizing, then drawing a shape, and then choosing the appropriate tool for creating it. Shaping techniques of all kinds are covered here — from the simplest ones to more complex bending and carving.”
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
While our website has the most comprehensive list of all of our tools, sometimes it's nice to flip through the pages of a good old fashioned catalog. This contains only our most popular permanent products that we manufacture just outside of Cleveland, OH. We will be happy to send you one at no charge. Just click the order button below so we can get the address you would like it sent to.
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
Chan’s desire for strong, lasting, easily repeated joints using power tools makes for a fun and educational read. He also has a strong interest in traditional Chinese furniture, and shows how some of those joints can be cut with power tools. This book will not only teach you how to machine about 100 useful joints, but will also open your eyes to using new, fun to make joints in upcoming projects. Chan assumes readers know how to use their machinery and power tools, so he focuses on the procedures required to produce the included joints.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference