I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.

The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here


Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.

If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?


The Winter 2018 issue of Scroll Saw Woodworking & Crafts features a variety of projects, patterns, and features, as well as interesting techniques. This issue is a part of the regular magazine subscription. It is also available from your favorite retailer or from Fox Chapel Publishing, www.foxchapelpublishing.com, 1-800-457-9112.       In This Issue Scroll down […]
Woodworking Books go hand in hand with the tools and the work. Whether you are a beginner or a master woodworker there is always a new technique or a great tip waiting for you on the pages.  We have hundreds of woodworking books to choose from, written by woodworking authors who understand the craft and know the trials and tribulations of the path.

This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.

I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
We offer top quality woodcraft products. When it comes to quality, dedication and a commitment to excellence we can't be beat! We have a large selection of online craft supplies for the hobbyist or the professional woodcrafter. We're dedicated to meet your craft and woodcraft products needs. Check out our online store and let us help you make your next woodcraft projects shine!
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Beyond the weight capacity, the Grizzly is also the largest table top on our list and in more ways than one. For a workspace, the Grizzly provides 5’ of length by 2 ½’ of width. There is not another table that really comes close to that size. Another size advantage of the Grizzly bench is the table top’s thickness. While the standard thickness of the table top for a quality woodworking bench is 1” with lesser models often offering only ¾” of thickness, the Grizzly provides a 1 ½” thick table top.
×