Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.

Tapping the knowledge of dozens of top-shelf woodworkers, Scott Landis’s The Workbench Book, and Jim Tolpin’s The Toolbox Book are filled with inspirational photos and drawings that you can use to enhance your workbench and tool storage needs. John White’s Care and Repair of Shop Machines completes the workshop triumvirate. The author’s straightforward advice for repairing and setting machinery will help you make the most of every machine in your shop.


One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
The Woodworker's Library™ offers hundreds of books, plans, and videos on topics related to woodworking, arts and crafts, home improvement, woodworking tools, furniture, and much more — many at discount prices. We make every effort to keep our catalog up-to-date in order to offer you the widest selection of quality titles to choose from. Browse our extensive book catalog and shop online. We hope you enjoy your visit.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
As a tribute to Tage Frid who passed away in 2004, combined with the 30th anniversary of The Taunton Press, this three-volume slipcase set is the most complete, authoritative guide to woodworking for readers of all skill levels. The books in the slipcase include: “”Book 1: Joinery,”” “”Book 2: Shaping, Veneering, Finishing,”” and “”Book 3: Furnituremaking,”” The techniques illustrated in these books are demonstrated step by step, with clarity and organization that allows readers to understand and carry out virtually any woodworking project.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.

In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.
×