Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
Projects to build on. Korn's book includes basic projects that you can put your own spin on. This Shaker footstool was inspired by one of the projects in his book. The last side-table project in his book (pictured) has the same pedigree as these two other FW projects: Tim Rousseau's small cherry cabinet and Stephen Hammer's small stand with coopered panels.

We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.

Remember those fire safety tips you used to get in grade school, about the dangers of oily rags? It was linseed oil they were talking about. All oily rags are dangerously flammable. Linseed oil will self-combust. Linseed oil doesn't evaporate, it oxidizes. The oxidization generates heat, and the increased temperature increases the rate of oxidation.
As I was handling the 2x4's, during the routing, I realized that I really wouldn't be happy with the look of the bench, if it were made from these unfinished boards. They had stamps, pencil marks, and more importantly, incipient splinters left by the saw, none of which I wanted. And I was remembering what other shop furniture made from unfinished pine had looked like, after a few years in the grime of a shop.
One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).

This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.

One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).


With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
“This hardcover book with internal spiral binding is 6.5in x 8in, a perfect size for carpenters and woodworkers to keep near their workbench or toolbox for quick access.The design of this book allows it to lay open flat, which allows for easy and frequent reference, and the interior photographs, illustrations and diagrams, make the learning process simple and fun for beginners, and provides useful tips for more advanced readers.
I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.
Though still straightforward in design, this bench distinguishes itself from many of its competitors with the sheer wealth of storage options. It includes two drawers of equal size with an additional drawer of double size as well as a spacious cupboard. Altogether, this provides for more storage space and organization than any other workbench we reviewed. Of course, this bench also comes with many of the same advantages and disadvantages that you would expect to see on other models within this lineup.
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
×