Woodworker’s Visual Handbook. This is a book for people like me, who can understand an idea faster if they see it than read about it. Woodworker’s Visual Handbook has more than 1,300 illustrations and 430 pages of advice that visually explain such issues as how to install smooth-sliding drawers in frame-and-panel cabinets, how to lay out a complicated project and cut the joints, and the pros and cons of working with more than 60 species of wood (a topic on which author Jon Arno was an expert). There’s even a section on furniture styles, another topic Jon knew well.
You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.
```1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
```

Proportion is the correlative relationship of all the parts to the whole. Although proportion usually refers to size, it is also a way to compare harmony between colour, quantity, placement and degree. Proportion is achieved when all sizes, shapes, textures, colors and so on complement one another. Remember that the eye appreciates some differences and may find equal parts monotonous and boring. Dividing space into equal parts such as halves, quarters and thirds is predictable and as a result the eye often skips past it.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
As a teacher I find Ernest Joyce’s “The Technique of Furniture Making” (Batson) invaluable, ’tho it is as far away from an enjoyable read as possible. Similarly Bob Wearing’s “Essential Woodworker” (Lost Art Press). Bob is one of the only people who ever gave insight into traditional English technique. I believe the lack of similar books is due to the apprenticeship tradition of teaching, where nothing was ever written down.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
```Remember those fire safety tips you used to get in grade school, about the dangers of oily rags? It was linseed oil they were talking about. All oily rags are dangerously flammable. Linseed oil will self-combust. Linseed oil doesn't evaporate, it oxidizes. The oxidization generates heat, and the increased temperature increases the rate of oxidation.
```

Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
Tom Fidgen, a regular contributor to our maga­zine, works only with hand tools, so he has a slightly different way of looking at a project – and an honest respect for good, old-fashioned hard work. He seems to appreciate the small things in woodworking, gaining great satisfaction from a smoothly planed surface or a strong mor­tise and tenon joint, and it rubs off. Made by Hand takes the reader through the entire process of making six different projects with nothing but hand tools. He talks a lot about the phi­losophy behind his style of working and how you can bring some of the simple life into your next project. He doesn’t hit you over the head with electricity guilt – he realizes that balance is what most people ought to strive for. Tom’s welcoming, open writing style is also a nice surprise. It’s almost like you’re having a conver­sation with him right in your living room, discussing what really matters in woodworking.
One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.