Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
Pyrography Workbook: A Complete Guide to the Art of Woodburning. It’s amazing what you can create with woodburning. You can make art that stands on its own, or use woodburning to personalize your crafts. In her book, Sue Walters talks about equipment, techniques, and safety. She also takes you step-by-step through 3 different projects for the beginner, intermediate, and the advanced woodburner. When I bought my first wood burner, I automatically purchased this book as well.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.

You can bookend my 30 years of woodworking with two volumes. Roy Underhill’s “The Woodwright’s Shop: A Practical Guide to Traditional Woodcraft” (U of North Carolina P) marks the beginning. Today, Steven W. Semes’ “The Architecture of the Classical Interior” (Norton) makes sense of all the conflicting mishmash of “design speak” tossed about. Hope I have another 30 years in me so the Semes book will someday be a midway milepost in a long, rewarding journey.

Thanks! Great information. As an advanced novice worker, I finally decided to build my first bench a couple years ago. After reading several of your blogs knowing full well mortised dove tale leg joinery is yet beyond my capability, I elected to build Robert Lang’s “21st Century Workbench”. I also chose his VERITAS Twin Screw Vise in the face vise position. Used an old Craftsman face vise in the tail vise position. Constructed of laminated 9/4 x 31/2″ Pecan and 60″ long because of my small crowed shop. Super happy to this point. As I mature in woodworking I may live to construct one of a different choice at a latter date, but I’m 73 so we’ll see. Thanks again for the advise.


Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.

​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
Pattern is the ordered repetition of an individual element. Pattern needs repetition in order to be considered a pattern. However, as already mentioned elsewhere, repetition can become boring. Slight variations in a pattern break monotony and add life to it. This also makes a pattern more familiar, especially if it relates closely to patterns found in nature. If a pattern is being created using a decorative motif, consider the dimensions of the surface area on which the motif will be seen to determine the motif’s scale. Larger surfaces can support a larger motif and allow the viewer to fully appreciate the impact of the repetition. If the motif is too small, it can be distracting and make the area feel busy.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.

Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

As a teacher I find Ernest Joyce’s “The Technique of Furniture Making” (Batson) invaluable, ’tho it is as far away from an enjoyable read as possible. Similarly Bob Wearing’s “Essential Woodworker” (Lost Art Press). Bob is one of the only people who ever gave insight into traditional English technique. I believe the lack of similar books is due to the apprenticeship tradition of teaching, where nothing was ever written down.


Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.

When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
Time for Geometric Shapes – Neil Moledzki Tribute clock is a reproduction of a clock made by James Krenov. The sweeping curves and the impression we get of the clock weighing down the stand produces an organic and even animated feel to the piece. It should be noted that something that has an organic feel is not the same as having an organic shape. If we break the parts down on the clock, we can see it is made entirely of geometric shapes.
I’ve seen antique cabinetmakers’ benches that are sixteen and seventeen feet long, more than three feet wide, and supported by a dozen drawers and doors—and that weigh as much as a felled oak tree. In contrast, jewelers’ cabinets seem to be on a dollhouse scale, with tiny tools to match. For most of us, however, space limitations preclude the biggest, and the smallest are just not big enough.
1. Cabinet Making and Millwork by John L. Feirer. I read this book cover to cover when I first got into woodworking, and its still my number one reference book when researching a project or technique. I believe it was intended as a textbook for a high school shop class, so it's laid out in great 101 style. It includes descriptions of everything from how sandpaper is made to best practices for shop math, and provides details for both hand and power tools.
This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.
×