Time for Geometric Shapes – Neil Moledzki Tribute clock is a reproduction of a clock made by James Krenov. The sweeping curves and the impression we get of the clock weighing down the stand produces an organic and even animated feel to the piece. It should be noted that something that has an organic feel is not the same as having an organic shape. If we break the parts down on the clock, we can see it is made entirely of geometric shapes.
The original design had a height of 35-1/8". Their two-layer top was 1-1/2" thick, so their legs were 33-5/8" long. I want a height of 35", but I'm using a top that's 3" thick. My basement floor is anything but level, so I'm using levelers that are adjustable from 3/4" to 1-1/2". In other words, I want legs that are around 31-3/4" long. (If you're not using levelers, your legs need precise lengths. The levelers give about 3/4" of adjustment, so precision is less necessary.
Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
Drill a pair of 3/8" holes in each end of the short stretchers, just over half of the depth of the dowels, using a brad-pointed bit. These stretchers already have a groove running their length, centered on the bottom edge. Precise placement isn't necessary, but keeping track of which part is which is. We need a hole in each end of each stretcher. Take care to keep these holes square, you don't want them running at angles.
```With more than 1,800 drawings, diagrams and photos, this authoritative guide encompasses the whole art and craft of woodworking. Designed to instruct and inspire every woodworker from the beginner to the most exacting expert, it has become a classic. It includes a discussion of all the principal hardwoods and softwoods, how to choose and use hand tools, detailed information on every woodworking technique–jointing, bonding, fastening, laminating, and much more.
```

As a tribute to Tage Frid who passed away in 2004, combined with the 30th anniversary of The Taunton Press, this three-volume slipcase set is the most complete, authoritative guide to woodworking for readers of all skill levels. The books in the slipcase include: “”Book 1: Joinery,”” “”Book 2: Shaping, Veneering, Finishing,”” and “”Book 3: Furnituremaking,”” The techniques illustrated in these books are demonstrated step by step, with clarity and organization that allows readers to understand and carry out virtually any woodworking project.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
With more than 1,800 drawings, diagrams and photos, this authoritative guide encompasses the whole art and craft of woodworking. Designed to instruct and inspire every woodworker from the beginner to the most exacting expert, it has become a classic. It includes a discussion of all the principal hardwoods and softwoods, how to choose and use hand tools, detailed information on every woodworking technique–jointing, bonding, fastening, laminating, and much more.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.
Time for Geometric Shapes – Neil Moledzki Tribute clock is a reproduction of a clock made by James Krenov. The sweeping curves and the impression we get of the clock weighing down the stand produces an organic and even animated feel to the piece. It should be noted that something that has an organic feel is not the same as having an organic shape. If we break the parts down on the clock, we can see it is made entirely of geometric shapes.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
“With Hammer in Hand” by Charles F. Hummel (UP Virginia). Resurfacing like Brigadoon, the woodworking shop of the Dominy family was sealed up with the tools still on the benches and saws still sharp. Moved to the Winterthur Museum, the workshop is an open portal into village woodworking in early America. Hummel’s book takes it tool by tool, piece by piece, expanding our view with a true scholar/craftsman’s eye.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!
You can bookend my 30 years of woodworking with two volumes. Roy Underhill’s “The Woodwright’s Shop: A Practical Guide to Traditional Woodcraft” (U of North Carolina P) marks the beginning. Today, Steven W. Semes’ “The Architecture of the Classical Interior” (Norton) makes sense of all the conflicting mishmash of “design speak” tossed about. Hope I have another 30 years in me so the Semes book will someday be a midway milepost in a long, rewarding journey.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
2. Bill Hylton's Power-Tool Joinery by Bill Hylton. From the editors of Popular Woodworking magazine, this is a go-to for setting up power tools for making joinery. Organized by joint type - rabbets, half-laps, dovetails, etc - it provides detailed instructions show you how to make each joint with every tool possible. I especially like the jigs and fixtures details that show you there's definitely more than one way to skin that cat.
The latest edition of this highly regarded instructional manual. See the great reader reviews posted for the previous editions. With this book and a weekend of your time you can make a plane and learn to use it effectively. You’ll also discover a wealth of general woodworking tips and acquire a solid grounding in many fundamentals of fine woodworking. Now in its third printing, “Making and Mastering Wood Planes” by master craftsman David Finck is the definitive book in the field and a classic introduction to the art of fine woodworking.
```Mine is similar but a bit more robust. The top is a sandwich, two 18mm sheets of WBP ply with an 18mm mdf filling. The legs are mortise and tenoned together, the ends glued and pegged, the stretchers are joined with long bolts so it comes apart. I stiffened it by adding a very closely fitted cabinet underneath (it had to go in dead square) and it is now absolutely rock solid.
```

##### Even in today’s world of electric machinery, when most people were asked to name a woodworking tool, planes and scrapers would probably be at the top of the list. They are as useful now as they were years ago but, because of their electrified cousins, they are often overlooked in favour of a faster option. In this compre­hensive book, John English explains what each type of plane is for, how to set it up for optimal performance and how to use it. The text is thorough and the photos are informative. All in all, this is a good read for a beginning or intermediate woodworker. Or a woodworker who simply never gave hand planes and scrapers a fair shake.

Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong