Furniture with Soul sheds light on some of the worlds most respected and revered makers of fine furniture. Going into their shops and learning how they got into the craft, what they most enjoy about it, and hearing some funny stories along they way is what this book is all about. It’s not a how-to in any way, unless you’re talking about how these selected group of makers made a living creating exquisite works of art. Beautiful photos of creative and challenging pieces of furniture are included throughout. My favourite book from the last year.
Professional woodworker Jim Tolpin offers solid instruction on the principles of measurement and proportion, walking you through every step of the woodworking process. From design and layout to developing a cutting list, his easy-to-follow style introduces a variety of tools (new and old) used to transfer measurements accurately to the wood. You’ll learn the best cutting techniques, how to prevent mistakes before they happen, and for those unavoidable mistakes, you’ll learn how to fix them so no one will know!
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
When the shelf was full, we called the list done. The results of that debate is the list of books that follows (publishers listed are for the editions we own). It’s by no means a perfect list. It is a list that would probably change a bit if we had the debate again in a couple months. Some of these are classics, some are contemporary. But these are the books that are first in our hearts.
Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).
Finishing is often an afterthought and spraying a finish isn’t exactly the first technique discussed when the topic does come up. While it’s often easier to wipe on a couple of coats of finish and be done with it, there are times when spraying a finish makes the most sense. There are many advantages to spraying a finish but there are some drawbacks too. Spray Finishing Made Simple does what it claims – it takes an imposing, unfamiliar topic and makes sense of it. This book is for the first-time spray finisher, as it starts with the basics and progresses through the stages. Don’t let the unknown stand in your way if you’re interested in learning about spraying. Pick up this book and get spraying.
I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
This is technically a vanity factor, though the ability to store tools and other supplies at quick reach can be a time and energy saver. At the least, you will want a bench that comes with a shelf underneath. This will allow the storage of larger items that can otherwise be difficult to find a place for. Drawers are the other popular storage for benches and can make retrieving tools much easier – just make sure the inside of the drawer is lined with felt or the wood may prematurely dull your tools.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.