Ok, I’ve had my morning coffee and now it’s about time to get out to the shop to see what I can do to make that bench a little more pleasing to my eye. I like that Craftsman flair idea. That was my intent at the time I built it, too bad I got lazy and rushed the job. It’s not like I was going to make hundreds of benches for someone else and would never see it again. I should have taken the time to make it the way I wanted it to look. This could keep me entertained for awhile. I see major surgery in the forecast! Gotta plan it all out just right.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
The end vise will have both jaws made out of 1-1/2" thick oak. The front vise has its moving jaw made of 1-1/2" oak, but uses the edge of the bench as its stationary jaw. So while for the end vise, if we mount it lower, we can make both the jaws deeper to compensate, for the front vise we cannot, so we want it mounted as close to the edge of the bench as possible.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
I will admit, I'm not a pyrography genius. In fact the last time used a woodburning tool, it was Christmas Day and was about five years old. It didn’t go well. A lot has changed since then. The tools have improved, there is a large and growing group of woodburning artists and there are great books to show you the basics and inspire you to pick up the art of pyrography. Woodburning with Style is the perfect book if you’re just learning. Not only will it teach you about the equipment available, it covers decorative techniques, lettering, portraits and more, before providing a chapter of inspirational projects and photographs to really get your imagination going. Pyrography is an art in itself but can also be used in conjunction with turnings, carvings or furniture making.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.
Cabinetmaking at the highest level is an art, a discipline, a philosophy–even a way of life–in addition to being a useful craft. In this book one of the greatest living cabinetmakers reflects on the deeper meanings of his craft and explains for less accomplished workers how the right attitudes toward materials, tools, and time can increase the joys of this complex activity. Craftspeople in every medium will be inspired by this account of getting started and developing habits that lessen the difficulties of a complex craft.
We will charge the payment method listed in Magazine Subscription Manager. If we cannot successfully charge this payment method, we will use the payment method you gave us when you originally placed your order. If we cannot successfully charge that payment method, we'll use another payment method you have saved in your Amazon.com account. Your initial sign-up is an authorization for us to use the preferred or other available payment methods to pay for your subscription.
Shape is critical to the ultimate success or failure of a piece of furniture. Knowing this, custom-furniture maker Lonnie Bird has taken the complex subject of shaping and in this book made it accessible to every woodworker. He guides the reader toward first visualizing, then drawing a shape, and then choosing the appropriate tool for creating it. Shaping techniques of all kinds are covered here — from the simplest ones to more complex bending and carving.”
I just got this book a few days ago, and I've had a hard time putting it down. There are lots of full-color pictures, with thorough descriptions of almost every aspect of woodworking. I've already learned a lot about different types of wood, how to make several kinds of cuts with several kinds of tools (including suggestions for what to do even though I don't have a large selection of power tools), and have some projects picked out to start as soon as I can get the lumber! It is a very thorough book, unlike several others I looked through at my local bookstore. I would highly recommend it to anyone who's interested in woodworking! It is both fun and informative. Almost half of this substantial book is general background information and instruction, including a detailed glossary, and the rest is a good selection of detailed, well-illustrated plans.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
If you’re looking for fresh, simple projects that have a rustic touch to them, this is the book for you. Lubkemann has a way of finding a project in just about every part of a tree; from candle-holders, photo frames and salt shakers to coat trees, lamps and a checkers set, there are projects big and small. Whether you’re looking for some gift ideas or you want the odd project to keep you busy over the winter, I’m sure you will find something here.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.
The Workshop Book: A Craftsman's Guide to Making the Most of Any Work Space by Scott Landis. This is not a new book - it was written in 1987. And the photographs reflect that. But what it lacks in that flip-through-the-pictures-and-get-major-workspace-envy, it makes up for in the actual text. It provides, mostly, creative solutions for a variety of different tasks from real professionals working in limited space. If you're interested in upgrading your space or building your dream shop from scratch, this really is a good place to start. It doesn't have a ton of up-to-date and practical advice; its more of a reflection on the nature of workshops in all their variety. And that never goes out of style.
Woodworker’s Visual Handbook. This is a book for people like me, who can understand an idea faster if they see it than read about it. Woodworker’s Visual Handbook has more than 1,300 illustrations and 430 pages of advice that visually explain such issues as how to install smooth-sliding drawers in frame-and-panel cabinets, how to lay out a complicated project and cut the joints, and the pros and cons of working with more than 60 species of wood (a topic on which author Jon Arno was an expert). There’s even a section on furniture styles, another topic Jon knew well.
Skirting traditional woodworking – sometimes seemingly allergic to it – this book shows you things you didn’t think were possible with wood, and many things you wish you had thought of first. The variety of the finished pieces is wonderful and makes for a nice read. Including 89 artists in total, each brief section contains background information, inspirational thoughts and technical details on how each artist completes their work. Wood Art Today 2 covers furniture, turnings, boxes, sculptures and more. One of the things I like most about it is you can open it up to any page and start learning about a specific artist and the work they do. This one is a lot of fun.
Tools: I am inspired by tools, whether the tool is a good chef’s knife, a watercolor paintbrush or a lowly marking gauge. I find 18th-century tools particularly beautiful and elegant in their simplicity. To openly admit I am inspired by my tools makes me somewhat of a kook. But here, amongst friends, I suspect I am not alone. I’ve copied many tools in these books and sought tools that resembled these and been a happier person for it.
The Complete Manual of Woodworking A comprehensive book that covers tons of woodworking topics: woodworking design, hand tools, power tools, workshops, wood carving, joinery, finishing wood. You will also learn a lot about this natural resource we call wood. Filled with great photos, diagrams, and illustrations. If you want to branch out and explore other woodworking endeavors, you will enjoy owning this book.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
The base needs to be as wide as the sum of width of the guide strip and the distance from the edge of the shoe, plus a bit extra, With my saw, the overhang is 3-1/2", so I made my guide strip 5-1/2" wide. The distance between from the edge of the shoe to the blade is about 4-1/2", so the base needs to be at least 10" wide. Since I was working with a 24" wide sheet, I just sliced it down the middle.
A couple nice qualities about this bench include the weight and vice capacities. The weight capacity of this bench is 330 pounds which is decent, though it will not wow you too much. The vice, on the other hand, provides a 7” capacity which is tied for the most on our list. That said, there is only a single vice, and it is not able to be repositioned. This can make things a bit frustrating for lefties as it is a right-handed configuration.