I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
My woodworking mentor, Robert Van Norman, studied under the esteemed woodworker James Krenov. Robert remembers many of JK’s wise words, especially “trust your eye”. When it was time for me to hear those words, I remember feeling such relief and permission to embrace my inherent perspicacity. Intuition is essential in the design and creation process, and for developing work that reflects the maker beyond his or her technical skill alone. At times, the craftsperson is called on to explain the aesthetics of his design and saying “it just feels right” doesn’t always cut it. This article covers seven common design considerations, their definition and how they are generally accepted and understood. Not only will the article help increase design vocabulary and awareness, but it may also assist in problem solving and recognizing the aesthetic strengths and weaknesses of a furniture piece.
Colour Integration – Brian Newell creates a dynamic relationship between light and dark. Often, when contrast is employed, the focus is about the difference, but here Newell’s focus is about integrating the light and dark. This is achieved by using dark wood (Macassar Ebony), which also contains the same hue as the light wood (Pear), and by creating dark areas on the light wood from the negative space of the pierced carving and the pulls. (Photo by Yoshiaki Kato)
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
When this book showed up at my studio I was very sceptical. Yet another “book of every­thing”? But after spending only five minutes skimming through it, I learned about a couple of storage ideas my shop needed, some cool new jigs that would come in handy and a few tricks to make my time in the shop more enjoyable and productive. There will be hundreds of ideas in here you will have no interest in whatsoever, but that’s all right … there are over 650 ideas in total, so some are sure to tickle your fancy.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.

If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.


Colour Integration – Brian Newell creates a dynamic relationship between light and dark. Often, when contrast is employed, the focus is about the difference, but here Newell’s focus is about integrating the light and dark. This is achieved by using dark wood (Macassar Ebony), which also contains the same hue as the light wood (Pear), and by creating dark areas on the light wood from the negative space of the pierced carving and the pulls. (Photo by Yoshiaki Kato)

I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
×