Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.

The Complete Manual of Woodworking A comprehensive book that covers tons of woodworking topics: woodworking design, hand tools, power tools, workshops, wood carving, joinery, finishing wood. You will also learn a lot about this natural resource we call wood. Filled with great photos, diagrams, and illustrations. If you want to branch out and explore other woodworking endeavors, you will enjoy owning this book.


One thing that surprised me about the forthcoming article is that while some authors – James Krenov, George Nakashima, Roy Underhill and Bob Flexner– feature in both the list below and the “Young Makers’ Bookshelves” article, a lot of the titles on the upcoming list are new to me. So of course, I’ve ordered them (a disease for which there is no cure).
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.

The Joint Book contains easy-to-follow step-by-step instructions for creating edge and scarf joints, lapped and housed joints, mortise and tenon joints, miters and bevels, dovetails, dowels and biscuits, and provides detailed descriptions of fasteners, hardware, and knockdown joints. This book is the perfect companion for any woodworker interested in improving their joint-making skills.”
5. The Woodbook: The Complete Plates. This one contains no instructions, no techniques, and no how-to information. Rather, it's the most complete collection of American wood samples ever created. Assembled between between 1888 and 1913 by New Yorker Romeyn Beck Hough and originally published in fourteen volumes, Taschen's publication "reproduces, in painstaking facsimile, all of the specimen pages from the original volumes... For all trees, now arranged in alphabetical order, three different cross-section cuts of wood are represented (radial, horizontal, and tangential), demonstrating the particular characteristics of the grain and the wealth of colors and textures to be found among the many different wood types. Also included in this special edition are lithographs by Charles Sprague Sargent of the leaves and nuts of most trees, as well as texts describing the trees’ geographical origins and physical characteristics."
If you’re more interested in working with wood rather than machining it, you will be relieved to learn that expensive powered machinery isn’t required to build furniture. You can also forget the dust masks, face shields and hearing protection since many of the safety concerns related to woodworking—the use of power tools—are eliminated. In this book, you’ll learn to set up a hand-tool woodworking shop, then discover the toolset, practice the skillset, and understand the mindset—effectively completing a comprehensive course in hand-tool woodworking.

The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.
The next day, cut it flush. Use a block plane to ensure it truly is flush. This will be the top of the bottom layer of the bench top, so gouges aren't a problem. (Wiping up glue with a damp cloth can lead to stains and finishes applying unevenly. That won't be a problem here, either.) But bulges and bumps are a problem - they will keep the two layers of the top from matching up evenly.

The hits included Shop Tips, Woodworking: The Right Technique, Router Magic, Woodworker’s Problem Solver and the Woodworker’s Visual Handbook. Each of those books sold more than 100,000 copies because of the quality of the advice and projects. And the books still hold up well, as you can see if you view buyers’ comments on sites like Amazon, where most of the titles consistently receive 5-star ratings.


There are simple jigs like a trammel baseplate and T-square, but you’ll also find a vacuum-clamping jig you can use to rout surfaces without clamps getting in the way, a dowel-making fixture, and router jigs to help you make fluted columns and even flamed finials. Bill also included several variations of router tables, including an ultimate table I built for my own shop.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.

Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
Grizzly is a company currently undergoing an upheaval. This brand was once known as a manufacturer of professional grade tools and equipment for woodworking products. Though, in recent years, that reputation has begun to slip a bit since being bought by the Chinese company SIEG. These days, whether the Grizzly product stands up to its previous standards of excellence often has more to do with what you are buying than the company itself.
×