If you’re looking for fresh, simple projects that have a rustic touch to them, this is the book for you. Lubkemann has a way of finding a project in just about every part of a tree; from candle-holders, photo frames and salt shakers to coat trees, lamps and a checkers set, there are projects big and small. Whether you’re looking for some gift ideas or you want the odd project to keep you busy over the winter, I’m sure you will find something here.
Many kids have the natural desire to learn about tools and make wooden objects, but as adults it’s difficult to know where or how to start teaching. Kid Crafts Woodworking starts at the very beginning, with short sections on, among other things, the properties of wood, gluing and metal fasteners. Nothing long or boring, just the basics, for a kid-length attention span. With straightforward paragraphs and clear, simple photos, the book goes on to discuss the safe usage of basic tools. Then comes the fun part – the 21 projects. Easy-to-follow instructions will guide your child through the projects, but there’s no reason why you shouldn’t be there every step of the way. Just don’t get too eager and do all the work for them … it’s their project after all.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
The Handbuilt Home. Ana White has created a wonderful DIY book. It’s filled with 34 projects she describes as simple, stylish, and budget-friendly. And you’ve probably already guest that they are related to improving your home. Each project has diagrams and instructions. And she tells the level of difficulty and project costs. This book resonates with many readers who want to make things themselves, but they may not have the fancy tools or the budget. Ana shows you how to make beautiful and affordable DIY projects.
Professional woodworker Jim Tolpin offers solid instruction on the principles of measurement and proportion, walking you through every step of the woodworking process. From design and layout to developing a cutting list, his easy-to-follow style introduces a variety of tools (new and old) used to transfer measurements accurately to the wood. You’ll learn the best cutting techniques, how to prevent mistakes before they happen, and for those unavoidable mistakes, you’ll learn how to fix them so no one will know!
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
Whether you’re setting up a new shop or upgrading your old one, a good, sturdy workbench will almost surely be central to your plans. We can help. Our editors and contributors have produced more than two dozen articles and videos about benches and assembly tables. We’ve included everything from a simple but workable plywood bench to a classic hardwood bench complete with vises. You’ll also find full project plans, as well as tips for installing vises, making your bench portable, adding storage, and more. Some of our workbench plans are free, and the rest can be purchased in our store (check the links below).
One aspect of the Windsor Design that is hit or miss is the vice. Notice we have to use the singular when describing it because this is the first workbench that we have reviewed which features only one vice. To make matters more frustrating, the vice cannot be repositioned along the bench. That said, the vice does at least have the largest capacity out of any we reviewed. At 7” capacity, the Windsor Design vice can secure any size workpiece you may have.