You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.


If you opt for a bench with drawers or cabinets built into its base, don’t forget the toe spaces: Leave a space roughly three inches deep and four inches wide at floor level for your toes, just like kitchen cabinets. The absence of a toe space means you’ll be forever kicking the face or sides of the cabinets which is irksome and, with tools in hand, potentially dangerous. And you’ll have to lean over farther to reach the back of the benchtop.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
Featuring each piece in highly-detailed, exploded drawings and applying time-honored dimensions and ergonomic standards, this comprehensive visual sourcebook takes the guesswork out of furniture joinery, assembly, dimension, and style. Woodworkers of any skill level will benefit from more than 1,300 crisp and detailed drawings that explain classic solutions to age-old problems, such as hanging a drawer, attaching a tabletop, and pegging a mortise.”
Over 1,400 color photos and drawings illustrate the methods, from simple butt joints to angled tenons and complex scarf joints. A project as simple as a box, for example, has a dozen ways to solve the joinery question. And, since many joints can be used interchangeably, Joinery leads you through making the right choice for your project based on the function of the piece, the time you have to work on it, your skill level, and your tooling.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
 efore you cut your first board, you must have a design to achieve the results you're after. To create a workable design, you must understand important properties of the wood you will be using, methods for joining that wood, typical construction techniques that are appropriate for the type of project you are building, styles of craftsmanship that will enhance and compliment the environment where this project will be used, and finally how to think through and plan a project.	

First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
The Fall 2018 issue of Scroll Saw Woodworking & Crafts features a variety of projects, patterns, and features, as well as interesting techniques. This issue is a part of the regular magazine subscription. It is also available from your favorite retailer or from Fox Chapel Publishing,www.foxchapelpublishing.com, 1-800-457-9112.   In This Issue Scroll down for a […]
Abstract shapes are considered in two ways. Shapes that are difficult to identify and sit outside our daily visual experience are called abstractions. The others are highly stylized organic shapes that are recognizable and usually provide specific information. Letters of the alphabet and the male/female symbols for washrooms are examples of abstract images.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
You can bookend my 30 years of woodworking with two volumes. Roy Underhill’s “The Woodwright’s Shop: A Practical Guide to Traditional Woodcraft” (U of North Carolina P) marks the beginning. Today, Steven W. Semes’ “The Architecture of the Classical Interior” (Norton) makes sense of all the conflicting mishmash of “design speak” tossed about. Hope I have another 30 years in me so the Semes book will someday be a midway milepost in a long, rewarding journey.
Once you start spreading glue, you have maybe five minutes to get the two panels mated, aligned, and clamped together. So make sure you have everything on-hand, and you're not gong to be interrupted. Start squeezing out the glue on one MDF panel, and spreading it around in a thin, even coating, making sure you leave no bare areas. Then do the same to the other MDF panel. Then pick up the bottom panel and flip it over onto the upper panel. Slide it around some to make sure the glue is spread evenly, then line up one corner and drive in a screw. Line up the opposite corner and drive in a screw there. Clamp all four corners to your flat surface, then start driving the rest of the screws, in a spiral pattern from the center.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.

Our understanding of what makes pleasing proportion is deeply imprinted in our mind and of all the design elements is the least influenced by one’s cultural experience. Desirable proportion has long been based around ratios we see in nature with an emphasis on the human body. The “golden rectangle,” considered to be divine proportion, has been used since at least the Renaissance period in art and design and has largely influenced our common experience with architecture and design. In fact, we often don’t even see proportion until something is out of proportion.


Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.

Projects to build on. Korn's book includes basic projects that you can put your own spin on. This Shaker footstool was inspired by one of the projects in his book. The last side-table project in his book (pictured) has the same pedigree as these two other FW projects: Tim Rousseau's small cherry cabinet and Stephen Hammer's small stand with coopered panels.


We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.
 Watching all of these crafters for the past few weeks has not only been the highlight of my week, but it has inspired me to learn more about crafting and explore my own creativity through their different mediums. Inevitably, I fell down an internet rabbit hole of research and excitement (including Kristen McQuinn’s piece on Books About Traditional Crafts) and found myself enthralled by what I found on the craft of my childhood, woodworking.

Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.


Then I flipped the top and the base, lied up the base in the proper location relative to the top, I then positioned the front vise and the support MDF for the end vise, and marked the locations of the bolt holes. Then I flipped the base right side up, drilled small pilot holes from the bottom side where I had marked the locations, and then drilled shallow countersink holes from each side, then a through hole that matched the bolts. Finally I tried out the bolts and washers, and deepened the countersinks until the heads of the bolts were just below flush.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.

Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.
×