I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Ok, I’ve had my morning coffee and now it’s about time to get out to the shop to see what I can do to make that bench a little more pleasing to my eye. I like that Craftsman flair idea. That was my intent at the time I built it, too bad I got lazy and rushed the job. It’s not like I was going to make hundreds of benches for someone else and would never see it again. I should have taken the time to make it the way I wanted it to look. This could keep me entertained for awhile. I see major surgery in the forecast! Gotta plan it all out just right.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
Skirting traditional woodworking – sometimes seemingly allergic to it – this book shows you things you didn’t think were possible with wood, and many things you wish you had thought of first. The variety of the finished pieces is wonderful and makes for a nice read. Including 89 artists in total, each brief section contains background information, inspirational thoughts and technical details on how each artist completes their work. Wood Art Today 2 covers furniture, turnings, boxes, sculptures and more. One of the things I like most about it is you can open it up to any page and start learning about a specific artist and the work they do. This one is a lot of fun.
The Complete Manual of Woodworking A comprehensive book that covers tons of woodworking topics: woodworking design, hand tools, power tools, workshops, wood carving, joinery, finishing wood. You will also learn a lot about this natural resource we call wood. Filled with great photos, diagrams, and illustrations. If you want to branch out and explore other woodworking endeavors, you will enjoy owning this book.
Even in today’s world of electric machinery, when most people were asked to name a woodworking tool, planes and scrapers would probably be at the top of the list. They are as useful now as they were years ago but, because of their electrified cousins, they are often overlooked in favour of a faster option. In this comprehensive book, John English explains what each type of plane is for, how to set it up for optimal performance and how to use it. The text is thorough and the photos are informative. All in all, this is a good read for a beginning or intermediate woodworker. Or a woodworker who simply never gave hand planes and scrapers a fair shake.
Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
Professional woodworker Jim Tolpin offers solid instruction on the principles of measurement and proportion, walking you through every step of the woodworking process. From design and layout to developing a cutting list, his easy-to-follow style introduces a variety of tools (new and old) used to transfer measurements accurately to the wood. You’ll learn the best cutting techniques, how to prevent mistakes before they happen, and for those unavoidable mistakes, you’ll learn how to fix them so no one will know!
With more than 1,800 drawings, diagrams and photos, this authoritative guide encompasses the whole art and craft of woodworking. Designed to instruct and inspire every woodworker from the beginner to the most exacting expert, it has become a classic. It includes a discussion of all the principal hardwoods and softwoods, how to choose and use hand tools, detailed information on every woodworking technique–jointing, bonding, fastening, laminating, and much more.
The last thing is to semi-permanently attach the bolts for the vises. Given the amount of work necessary to get to the bolt heads, once the top is joined, I had intended to tighten them up so they wouldn't spin, and lock them that way with blue Loctite. (That's the strongest non-permanent grade.) That didn't work. What I found was that the bottoms of the countersinks weren't quite flat, and when I tightened the nuts down that far, the ends of the bolts would be pulled far enough out of alignment that the vise bases would no longer fit. In order for the vises to fit over the bolts, I had to leave the nuts loose enough that the bolts had a bit of wiggle - which meant that they were almost loose enough for the bolts to spin. So I put Loctite on the nuts, to keep them from unscrewing, and filled the countersinks with Liquid Nails, in hopes of keeping the bolts from spinning. I considered using epoxy, or a metal-epoxy mix like JB Weld, but I didn't have enough of either on hand. It seems to be working for now, though the real test won't be until I have to take the vises off.
While our website has the most comprehensive list of all of our tools, sometimes it's nice to flip through the pages of a good old fashioned catalog. This contains only our most popular permanent products that we manufacture just outside of Cleveland, OH. We will be happy to send you one at no charge. Just click the order button below so we can get the address you would like it sent to.
As I was handling the 2x4's, during the routing, I realized that I really wouldn't be happy with the look of the bench, if it were made from these unfinished boards. They had stamps, pencil marks, and more importantly, incipient splinters left by the saw, none of which I wanted. And I was remembering what other shop furniture made from unfinished pine had looked like, after a few years in the grime of a shop.
I have picked out a list of 9 books on woodworking that covers a wide variety of woodworking hobbies and techniques. I can personally vouch for these books, since I own most of them. These books will serve as valuable reference tools that can be used over and over. I’ve also checked the ratings and comments to make sure these books resonate with their readers. For your convenience, I’ve also included Amazon affiliate links so you can check out the Amazon reviews yourselves. Hope you enjoy the article and towards the end, I will ask you to share your favorite woodworking books.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Even with all of those faults my only regret is that it is too ugly. I didn’t take the time to make it more visually attractive as I was eager to get right into making beautiful furniture instead. Twenty years later the furniture is still beautiful (or not) but I go out to the shop and look at a drab uninspiring workplace. Yeah, nothing wrong with having a visually inspiring workplace in my opinion. All that shop furniture I slapped together years ago with no concern about aesthetics is getting replaced bit by bit. Why should my shop be downright ugly when it is one of my favorite places in the world to spend my time? I see no reason for that, but that’s just my opinion and as we all know everyone has their own one of those… Sadly, no one pays nor reveres me when I offer mine. bummer, I could be a rich egotistical maniac if they did coz I sure offer it enough. 😉
As I try to improve as a woodworker and artist, I really want every piece to be better than my last. But this piece will always hold a special place in my ❤️ This table is made of 1250+ pieces of recycled skateboards and walnut, but If you count the individual veneers of the recycled skateboard pieces then it’s made of over 6,800 pieces of wood. 📷 @fvcksandflamingos 😘 #upcycledskateart
Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference
Of course, few benches can be ideal, and this one does have some drawbacks. That being said, most of the disadvantages of this bench are minor annoyances rather than deal breakers. For instance, this bench does not include any kind of storage whatsoever. Though, it does have the option of adding numerous additional features like a storage area. Still, for the bench, you would expect a drawer at the very least, maybe a shelf below the main table area.