To develop the material, we editors asked ourselves—and dozens of top woodworkers—what’s likely to go wrong at each stage of a project. We really dug deep to make sure we didn’t just repeat the types of advice you see in the average magazine. We ended up with a list of more than 500 problems covering everything from design and layout, to stock preparation, joinery, finishing and more. Then, we reached out to top woodworkers around the country for their solutions. The result was a 320-page book filled with some of the best advice you could ever find from more than 75 master craftsmen, including Marc Adams, Mike Dunbar, Graham Blackburn, Toshio Odate, David Marks, Frank Klausz and Lonnie Bird.
Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.

A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
Once you've placed an order at Amazon.com, it can take one to two weeks for your subscription to be received and scheduled by the publisher. Your subscription is then added to the publisher's next production cycle and shipped via standard mail. For example, if your monthly subscription was ordered and received by the publisher in November, and the December issue has already shipped, your order may be added to the January mailing. You can find out more information, including how to contact the publisher about your subscription, in Amazon's Magazine Subscription Manager.
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.

Once you start spreading glue, you have maybe five minutes to get the two panels mated, aligned, and clamped together. So make sure you have everything on-hand, and you're not gong to be interrupted. Start squeezing out the glue on one MDF panel, and spreading it around in a thin, even coating, making sure you leave no bare areas. Then do the same to the other MDF panel. Then pick up the bottom panel and flip it over onto the upper panel. Slide it around some to make sure the glue is spread evenly, then line up one corner and drive in a screw. Line up the opposite corner and drive in a screw there. Clamp all four corners to your flat surface, then start driving the rest of the screws, in a spiral pattern from the center.
The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.
Woodworking Business is an informative, common-sense-based book that may answer many questions for the amateur wood­worker who is considering going professional. This is not a gorgeous book. It doesn’t have glossy photos or beautiful graphic design. What it does offer is practical, down-to-earth tips while forcing you to consider the toughest question of all: Is running your own business right for you? Chapter topics include Setting Prices, Contracting Jobs, Getting Help and Everyday Lessons. Although it’s written from an American perspective, most of the information is pertinent to a Canadian reader.
We offer top quality woodcraft products. When it comes to quality, dedication and a commitment to excellence we can't be beat! We have a large selection of online craft supplies for the hobbyist or the professional woodcrafter. We're dedicated to meet your craft and woodcraft products needs. Check out our online store and let us help you make your next woodcraft projects shine!
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.

I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.


This is, as the title states, a book that details some incred­ibly advanced veneering techniques. If you have a solid foundation in basic veneering, and want to see what else can be done with this wonderful medium, this book will have you laying out veneer in ways you’ve never previously dreamt of. It will also have you asking yourself what else is possible. The extremely detailed step-by-step photos keep you visually onside with what Grove is doing, as words (as clear and concise as they are) are not enough.
Dark colours appear heavier and create a feeling of stability, whereas light colours hold less visual weight and can appear unstable. When joining woods of dark and light colour, the visual effect of heavy and light suggest that darker woods work better when used on the bottom. A suggestion from my mentor to help getting proportions right was to spray paint mock-ups with a colour similar to the woods to be used later.
Of all the machines in a workshop, we think two deserve their own books, not just because they possess the greatest potential, but when used incorrectly, are most likely to bite back. Bill Hylton and Fred Matlack’s Woodworking with the Router comes close to being the Router Bible. This tome provides an excellent overview of routers and bits while also explaining how to build and use jigs for router tables and handheld routing. Similarly, Paul Anthony’s Complete Illustrated Guide to Tablesaws gives entry-level and experienced woodworkers the information they need to safely use this workshop workhorse and accomplish more with their saws. Both books have excellent photos and great illustrations.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.

My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…


Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
1. Cabinet Making and Millwork by John L. Feirer. I read this book cover to cover when I first got into woodworking, and its still my number one reference book when researching a project or technique. I believe it was intended as a textbook for a high school shop class, so it's laid out in great 101 style. It includes descriptions of everything from how sandpaper is made to best practices for shop math, and provides details for both hand and power tools.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
×