The Gempler’s Farm Supply Catalog has been a leading source for farm and outdoor work supplies for over 25 years. You’ll find all your old favorites and essential supplies. With 35,000+ products from work gloves to long-handled tools, Gempler’s makes it easy to find the gear you need to get the job done. Print and online catalogs available on request.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
Woodworking Business is an informative, common-sense-based book that may answer many questions for the amateur woodworker who is considering going professional. This is not a gorgeous book. It doesn’t have glossy photos or beautiful graphic design. What it does offer is practical, down-to-earth tips while forcing you to consider the toughest question of all: Is running your own business right for you? Chapter topics include Setting Prices, Contracting Jobs, Getting Help and Everyday Lessons. Although it’s written from an American perspective, most of the information is pertinent to a Canadian reader.
I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-standard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a collection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting something different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
Big Book of Scroll Saw Woodworking. This book is jammed packed with scroll saw projects. Sixty projects to be exact. Topics include working with patterns, choosing materials, and blade selection. The projects are from many contributing experts on scroll saw woodworking. You’ll learn to make puzzles, boxes, toys, baskets, intarsia, portraits. Projects range from beginner to advanced.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
Beyond the weight capacity, the Grizzly is also the largest table top on our list and in more ways than one. For a workspace, the Grizzly provides 5’ of length by 2 ½’ of width. There is not another table that really comes close to that size. Another size advantage of the Grizzly bench is the table top’s thickness. While the standard thickness of the table top for a quality woodworking bench is 1” with lesser models often offering only ¾” of thickness, the Grizzly provides a 1 ½” thick table top.