With more than 1,800 drawings, diagrams and photos, this authoritative guide encompasses the whole art and craft of woodworking. Designed to instruct and inspire every woodworker from the beginner to the most exacting expert, it has become a classic. It includes a discussion of all the principal hardwoods and softwoods, how to choose and use hand tools, detailed information on every woodworking technique–jointing, bonding, fastening, laminating, and much more.
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.
Renewing Your Subscription: If you are ordering as a renewal to the same name and address as the current subscription, the publisher will add the Amazon order to your current subscription. For example, if you have 5 issues left and you add 12 through Amazon, you will now have 17 issues left on your subscription. Please note that the expiration date in the Magazine Subscription Manager will not reflect if you were already on file with the publisher. We will work with the publisher to ensure that you still receive all of the issues left on your subscription.
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.

I am surprised the the Hand and Eye combo by Tolpin didn’t make anyone’s list. I have also really found Chris Schwartz’s Anarchist’s design book very useful. Everything else that I really like is already in here somewhere; Moxon, Roubo, Estonia, Peart. The beginners book by Wearing is excellent, and I have taken to giving it to Eagle scouts at their Eagle Courts of Honor of late. (with an inscription about taking the raw stuff of life and developing the skills and tools to make from it what you need…); cheesy, I know, but it is a really good book to start folks off with.


Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.

I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.

Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
So since more than half the book is taken up with instruction, I thought there wouldn't be enough room for 40 projects. Thing is, the projects are mostly VERY simple and functional. There really does not seem to be any sort of eye towards craftsmanship and design. And they are almost all ugly. The picture frames included are literally the ugliest I've ever seen. Obviously, style is in the eye of the beholder, but I can't be making furniture to go in my home that looks like that, and my home is Ikea, Crate and Barrel, and Bombay to give you an idea.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
The Woodworker's Library™ offers hundreds of books, plans, and videos on topics related to woodworking, arts and crafts, home improvement, woodworking tools, furniture, and much more — many at discount prices. We make every effort to keep our catalog up-to-date in order to offer you the widest selection of quality titles to choose from. Browse our extensive book catalog and shop online. We hope you enjoy your visit.
5. The Woodbook: The Complete Plates. This one contains no instructions, no techniques, and no how-to information. Rather, it's the most complete collection of American wood samples ever created. Assembled between between 1888 and 1913 by New Yorker Romeyn Beck Hough and originally published in fourteen volumes, Taschen's publication "reproduces, in painstaking facsimile, all of the specimen pages from the original volumes... For all trees, now arranged in alphabetical order, three different cross-section cuts of wood are represented (radial, horizontal, and tangential), demonstrating the particular characteristics of the grain and the wealth of colors and textures to be found among the many different wood types. Also included in this special edition are lithographs by Charles Sprague Sargent of the leaves and nuts of most trees, as well as texts describing the trees’ geographical origins and physical characteristics."
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.

With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
Tools: I am inspired by tools, whether the tool is a good chef’s knife, a watercolor paintbrush or a lowly marking gauge. I find 18th-century tools particularly beautiful and elegant in their simplicity. To openly admit I am inspired by my tools makes me somewhat of a kook. But here, amongst friends, I suspect I am not alone. I’ve copied many tools in these books and sought tools that resembled these and been a happier person for it.
Be careful. Single 24x60" sheets of 3/4" MDF are pretty easy to lift. A doubled sheet is manageable. The countertop - 24x72" panel of 1-1/2" oak - weighs something over 100 pounds. It takes real care to lift safely. The joined top - 3" thick of oak and MDF - is past the range that can be lifted safely by one person. Don't try. Get a friend to help, or rig a block-and-tackle.
Woodturning: A Foundation Course When I decided to go beyond just turning writing pens, I turned to this book to help broaden my knowledge of woodturning. You will learn the tools of the trade and sharpening techniques for your turning tools. It introduces several turning projects like bowls, pepper mills, and table lamps. You also learn how to sand and finish your turned creations.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Professional woodworker Jim Tolpin offers solid instruction on the principles of measurement and proportion, walking you through every step of the woodworking process. From design and layout to developing a cutting list, his easy-to-follow style introduces a variety of tools (new and old) used to transfer measurements accurately to the wood. You’ll learn the best cutting techniques, how to prevent mistakes before they happen, and for those unavoidable mistakes, you’ll learn how to fix them so no one will know!
I have picked out a list of 9 books on woodworking that covers a wide variety of woodworking hobbies and techniques. I can personally vouch for these books, since I own most of them. These books will serve as valuable reference tools that can be used over and over. I’ve also checked the ratings and comments to make sure these books resonate with their readers. For your convenience, I’ve also included Amazon affiliate links so you can check out the Amazon reviews yourselves. Hope you enjoy the article and towards the end, I will ask you to share your favorite woodworking books.

Planing up some beautiful walnut for a charcuterie board this afternoon. I’ve been getting a lot of requests for some videos with tool-specific demos, and first on the list is how to properly sharpen and tune a handplane for efficient use. I’ll cover everything from what stones to buy to which jigs you need/don’t need. What other questions would you like to see get answered? #woodworking #handtools #shareknowledge #sharpening #buildlikeagirl #preservetradition
Once you start spreading glue, you have maybe five minutes to get the two panels mated, aligned, and clamped together. So make sure you have everything on-hand, and you're not gong to be interrupted. Start squeezing out the glue on one MDF panel, and spreading it around in a thin, even coating, making sure you leave no bare areas. Then do the same to the other MDF panel. Then pick up the bottom panel and flip it over onto the upper panel. Slide it around some to make sure the glue is spread evenly, then line up one corner and drive in a screw. Line up the opposite corner and drive in a screw there. Clamp all four corners to your flat surface, then start driving the rest of the screws, in a spiral pattern from the center.
A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.

We want to make these pieces square, and of identical length. Square is a matter of making sure the saw blade is square and that the cutting guide is square. The trick to getting the pieces of the same length is to clamp them together and to cut them all at once. For the 4x4's, that means making a rough cut in each first, so we have four pieces, each 3-4" longer than we need, from which we'll get our four legs.
Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.
I just got this book a few days ago, and I've had a hard time putting it down. There are lots of full-color pictures, with thorough descriptions of almost every aspect of woodworking. I've already learned a lot about different types of wood, how to make several kinds of cuts with several kinds of tools (including suggestions for what to do even though I don't have a large selection of power tools), and have some projects picked out to start as soon as I can get the lumber! It is a very thorough book, unlike several others I looked through at my local bookstore. I would highly recommend it to anyone who's interested in woodworking! It is both fun and informative. Almost half of this substantial book is general background information and instruction, including a detailed glossary, and the rest is a good selection of detailed, well-illustrated plans.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.
Finishing is often an afterthought and spraying a finish isn’t exactly the first technique discussed when the topic does come up. While it’s often easier to wipe on a couple of coats of finish and be done with it, there are times when spraying a finish makes the most sense. There are many advantages to spraying a finish but there are some drawbacks too. Spray Finishing Made Simple does what it claims – it takes an imposing, unfamiliar topic and makes sense of it. This book is for the first-time spray finisher, as it starts with the basics and progresses through the stages. Don’t let the unknown stand in your way if you’re interested in learning about spraying. Pick up this book and get spraying.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
As I try to improve as a woodworker and artist, I really want every piece to be better than my last. But this piece will always hold a special place in my ❤️ This table is made of 1250+ pieces of recycled skateboards and walnut, but If you count the individual veneers of the recycled skateboard pieces then it’s made of over 6,800 pieces of wood. 📷 @fvcksandflamingos 😘 #upcycledskateart
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
I’ve built workbenches with more than 100 students. In every class, there’s one guy who wants to put a vise on every corner of the bench. Not because it’s a partner’s bench for two people. Just because he wants it that way. While I support your freedom to choose, I also don’t want to spend two weeks installing complex tail-vise hardware on your bench when we could be building furniture instead.
×