Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
The good news is that you don’t need a lot of shelf space to house a comprehensive collection of basic woodworking knowledge. Get started with Understanding Wood. In this comprehensive bible, professor Bruce Hoadley delves into the nature of wood and how its structure affects strength, workability, and other characteristics. He then shines a light on fundamentals like drying, machining, bending, joining, sanding, gluing, often accompanied by stunning macro photographs that zoom you in to the meat of the matter.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
Stop it. Really. I mean it. Pick a height between your thigh and waist that seems right. You’ll adapt. Don’t worry about your back. You’ll adapt. If you are really uncertain, make it a little taller and then cut down the legs. After a decade or so, your work habits will put a magic number in your head. You’ll have built enough furniture that you will know your number. Until then, pick a number.
Woodworkers like books. Maybe it’s because they’re somehow still a wood product, but let’s face it, they travel into the shop well, offer great how-to instruction with pictures and words, and you can make notes in the margins if you like. Our fine woodworking books cover all the topics for which you’re looking: furniture plans; hand tool techniques; shop projects; wood finishing advice and much more.
This book addresses a key dilemma of the beginning woodworker: how do you build good projects without the basic shop furnishings to get the job done? And, why struggle with makeshift workshop equipment when you can create your own? Now you have the guidance of an expert woodworker to help you build workshop basics that you will use for years to come.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
4. Taunton's Complete Illustrated Guide To Finishing by Jeff Jewitt. This isn't the only book on the subject, but it's a great place to start. The real strength here is the bounty of color photos, which show exactly what's happening as you finalize your projects. It discusses finishing new projects, but also repairing old finishes and matching vintage pieces. It's not a "start here, end there" walk through, so you'll need to familiarize yourself with the way it's organized before beginning a project, but it is indeed a "complete illustrated guide" with encyclopedic-like thoroughness. Belongs in every library.
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
This instructable shows how to build, with basic tools and readily-available lumber, a bench that provides most of the function of a traditional woodworker's workbench. I began with a design by Asa Christiana that was featured in the second season of finewoodworking.com's video series Getting Started in Woodworking. The project plans are available on their website.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
“Traditional woodworking using hand tools can offer a more satisfying relationship with the wood and the creative woodworking process. It’s quieter, cleaner and maybe even a little spiritual. It’s no surprise that many “”plugged-in”” woodworkers are returning to the roots of this treasured skill. Where some hand-tool books focus solely on the use of hand tools, Made By Hand takes you right to the bench and shows you how to start building furniture using these tools.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Geometric shapes are made from straight or curved lines such as circles, squares and triangles. Their easy-to-recognize and often symmetrical patterns offer a sense of order, efficiency, strength, formality, but to some may be seen as uninteresting. Squares and rectangles are the predominant geometric shapes seen around us, not only in furniture, but in all areas of life. A circle has no beginning or ending, making it complete and inspiring thoughts of nature, perfection, unity, initiation and inclusion.
The Joint Book contains easy-to-follow step-by-step instructions for creating edge and scarf joints, lapped and housed joints, mortise and tenon joints, miters and bevels, dovetails, dowels and biscuits, and provides detailed descriptions of fasteners, hardware, and knockdown joints. This book is the perfect companion for any woodworker interested in improving their joint-making skills.”
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.
A great example that highlights our emotional connection to the rectangle and circle is to look at how these shapes have influenced table design. Rectangle tables have often been used in boardrooms and for formal dinners with, traditionally, the most important person being seated at the head of the table, which can perhaps create an instant hierarchy. A solution to this perceived inequality may have been found in the design of the round table, much favoured by King Arthur who considered his knights as equals.
Tapping the knowledge of dozens of top-shelf woodworkers, Scott Landis’s The Workbench Book, and Jim Tolpin’s The Toolbox Book are filled with inspirational photos and drawings that you can use to enhance your workbench and tool storage needs. John White’s Care and Repair of Shop Machines completes the workshop triumvirate. The author’s straightforward advice for repairing and setting machinery will help you make the most of every machine in your shop.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
One you have the vise jaws shaped so that the vise moves freely, mark and drill holes in the fixed jaw for the bolts that will hold it to the bench. With these drilled, reassemble the vise and mark the location of the holes with an awl. Disassemble the vise and drill the holes through the stretcher, then reassemble the vise and bolt the inner jaw in place.
Drill a pair of 3/8" holes in each end of the short stretchers, just over half of the depth of the dowels, using a brad-pointed bit. These stretchers already have a groove running their length, centered on the bottom edge. Precise placement isn't necessary, but keeping track of which part is which is. We need a hole in each end of each stretcher. Take care to keep these holes square, you don't want them running at angles.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.
When the shelf was full, we called the list done. The results of that debate is the list of books that follows (publishers listed are for the editions we own). It’s by no means a perfect list. It is a list that would probably change a bit if we had the debate again in a couple months. Some of these are classics, some are contemporary. But these are the books that are first in our hearts.
Our understanding of what makes pleasing proportion is deeply imprinted in our mind and of all the design elements is the least influenced by one’s cultural experience. Desirable proportion has long been based around ratios we see in nature with an emphasis on the human body. The “golden rectangle,” considered to be divine proportion, has been used since at least the Renaissance period in art and design and has largely influenced our common experience with architecture and design. In fact, we often don’t even see proportion until something is out of proportion.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Originally published at the turn of the twentieth century by an anonymous “Practical Joiner,” Woodwork Joints: How to Make and Where to Use Them remains an incredibly useful and practical guide for deciding which joints to use and how to make them the right way for carpentry, joinery, and cabinet-making. Here is the carefully illustrated source on joinery that not simply a collectible classic, but also a requisite and invaluable tool that withstands the test of time, containing more useful information than any other woodworking guide. Inside are illustrated instructions for making all kinds of joints, from simple to complex, suitable for novices and experts. The comprehensive list includes joints such as glued; halved; bridle; tongued and grooved; mortise and tenon; dowelling; scarf; hinged; shutting; dovetail and many more. Instructions specify which tools are required (i.e., planes, gauges, saws, chisels, the try square for testing purposes, etc.) and how to use them on each joint. Extensive chapters on each type of joint contain precise illustrations that make identifying joints for different purposes easy. Not a word is wasted in this short but entirely comprehensive guide, making Woodwork Joints the perfect aid for any joinery project.
1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!