Skirting tradi­tional woodworking – sometimes seem­ingly allergic to it – this book shows you things you didn’t think were possible with wood, and many things you wish you had thought of first. The variety of the finished pieces is won­derful and makes for a nice read. Including 89 artists in total, each brief section con­tains background information, inspirational thoughts and technical details on how each artist completes their work. Wood Art Today 2 covers furniture, turnings, boxes, sculptures and more. One of the things I like most about it is you can open it up to any page and start learning about a specific artist and the work they do. This one is a lot of fun. 


Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.

All glue & stain benches are made using a solid maple frame for lasting durability and strength. Side Clamp Benches are made specifically for bar clamps, and are used for gluing projects or clamp storage. Benches feature an open top with 17 sets of 3/4"W grooves that accept bar clamps measuring 3’ and over. Lower center rail is adaptable for storage of hand screws and C-clamps. Side clamp benches are available with or without a drip pan. Glue & Stain Benches are made with a 1-1/4” plywood top covered with heavy-coated galvanized steel. Bottom shelf has a 4” rear retaining lip. Glue and stain benches are available with or without casters. Limited Lifetime Warranty.

This is, as the title states, a book that details some incred­ibly advanced veneering techniques. If you have a solid foundation in basic veneering, and want to see what else can be done with this wonderful medium, this book will have you laying out veneer in ways you’ve never previously dreamt of. It will also have you asking yourself what else is possible. The extremely detailed step-by-step photos keep you visually onside with what Grove is doing, as words (as clear and concise as they are) are not enough.
The original design had a height of 35-1/8". Their two-layer top was 1-1/2" thick, so their legs were 33-5/8" long. I want a height of 35", but I'm using a top that's 3" thick. My basement floor is anything but level, so I'm using levelers that are adjustable from 3/4" to 1-1/2". In other words, I want legs that are around 31-3/4" long. (If you're not using levelers, your legs need precise lengths. The levelers give about 3/4" of adjustment, so precision is less necessary.
1. Cabinet Making and Millwork by John L. Feirer. I read this book cover to cover when I first got into woodworking, and its still my number one reference book when researching a project or technique. I believe it was intended as a textbook for a high school shop class, so it's laid out in great 101 style. It includes descriptions of everything from how sandpaper is made to best practices for shop math, and provides details for both hand and power tools.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
If the holes of the first jaw are in the proper position, drill holes in the same locations on the other jaw. I lined the drilled jaw on top of the undrilled jaw, clamped things down, and then drilled about 1/4" into the undrilled jaw, to mark the location. Then I removed the drilled jaw and drilled out the marked locations the same way I did the first.
5. The Woodbook: The Complete Plates. This one contains no instructions, no techniques, and no how-to information. Rather, it's the most complete collection of American wood samples ever created. Assembled between between 1888 and 1913 by New Yorker Romeyn Beck Hough and originally published in fourteen volumes, Taschen's publication "reproduces, in painstaking facsimile, all of the specimen pages from the original volumes... For all trees, now arranged in alphabetical order, three different cross-section cuts of wood are represented (radial, horizontal, and tangential), demonstrating the particular characteristics of the grain and the wealth of colors and textures to be found among the many different wood types. Also included in this special edition are lithographs by Charles Sprague Sargent of the leaves and nuts of most trees, as well as texts describing the trees’ geographical origins and physical characteristics."
Skirting tradi­tional woodworking – sometimes seem­ingly allergic to it – this book shows you things you didn’t think were possible with wood, and many things you wish you had thought of first. The variety of the finished pieces is won­derful and makes for a nice read. Including 89 artists in total, each brief section con­tains background information, inspirational thoughts and technical details on how each artist completes their work. Wood Art Today 2 covers furniture, turnings, boxes, sculptures and more. One of the things I like most about it is you can open it up to any page and start learning about a specific artist and the work they do. This one is a lot of fun. 

efore you cut your first board, you must have a design to achieve the results you're after. To create a workable design, you must understand important properties of the wood you will be using, methods for joining that wood, typical construction techniques that are appropriate for the type of project you are building, styles of craftsmanship that will enhance and compliment the environment where this project will be used, and finally how to think through and plan a project.
The jaw for the front vise needed to be 10" long - to span the distance from the leg to the end of the top, 1-1/2" thick - to allow for benchdog holes to be drilled in it, and 5" tall. The end vise was mounted 3/4" lower than the front vise, and the screw and guide rods were thicker, so its jaws needed to be at least 6-1/2" tall. Again, they needed to be 1-1/2" thick to allow for benchdog holes, and 23" long to span the width of the bench.

efore you cut your first board, you must have a design to achieve the results you're after. To create a workable design, you must understand important properties of the wood you will be using, methods for joining that wood, typical construction techniques that are appropriate for the type of project you are building, styles of craftsmanship that will enhance and compliment the environment where this project will be used, and finally how to think through and plan a project.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The bench I will be describing differs from both of these in a couple of areas, the most significant of which is the top. Allen's top was made from three layers of 3/4" medium density fiberboard (MDF), topped and edged with 1/4" hardboard. Christiana's top was just two layers of 3/4" MDF. My top is two layers of 3/4" MDF edged with 1/2" oak and topped by a 1-1/2" thick edge-glued oak Ikea countertop. My top is more expensive in both time and money than either Christiana's or Allen's. If you're looking to build something fast and cheap, I'd recommend Allen's approach over Christiana's. The hardboard significantly increases the durability of the top.
While our website has the most comprehensive list of all of our tools, sometimes it's nice to flip through the pages of a good old fashioned catalog.  This contains only our most popular permanent products that we manufacture just outside of Cleveland, OH.  We will be happy to send you one at no charge.  Just click the order button below so we can get the address you would like it sent to.  
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

There are simple jigs like a trammel baseplate and T-square, but you’ll also find a vacuum-clamping jig you can use to rout surfaces without clamps getting in the way, a dowel-making fixture, and router jigs to help you make fluted columns and even flamed finials. Bill also included several variations of router tables, including an ultimate table I built for my own shop.
If you’re even the slightest bit interested in the history of Japanese furniture, you will love this thorough collection of chests. The attention to detail is astounding, the photographs glorious and the historical insight intriguing. This is exactly what you would expect from a book that covers such a proud history of chest mak­ing on the land of the rising sun. Almost 100 pages of colour plates are complemented by information on typical construction materials, finishing techniques and regional charac­teristics. This book will please the antique collector, interior designer or wood­worker equally. 
“This hardcover book with internal spiral binding is 6.5in x 8in, a perfect size for carpenters and woodworkers to keep near their workbench or toolbox for quick access.The design of this book allows it to lay open flat, which allows for easy and frequent reference, and the interior photographs, illustrations and diagrams, make the learning process simple and fun for beginners, and provides useful tips for more advanced readers.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…

There are simple jigs like a trammel baseplate and T-square, but you’ll also find a vacuum-clamping jig you can use to rout surfaces without clamps getting in the way, a dowel-making fixture, and router jigs to help you make fluted columns and even flamed finials. Bill also included several variations of router tables, including an ultimate table I built for my own shop.

In order to complete your transaction, we will share the name, billing and shipping address and other order information associated with your purchase with the publisher or magazine vendor. Your name and address will also be shared with a circulation-auditing organization. We may share your e-mail with the publisher, but you can control how it will be used in Subscription Manager. We will not share your credit card information. Offers on this page are introductory. See Details.


MechanicGuides.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon(.com, .co.uk, .ca etc) and any other website that may be affiliated with Amazon Service LLC Associates Program. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
As a tribute to Tage Frid who passed away in 2004, combined with the 30th anniversary of The Taunton Press, this three-volume slipcase set is the most complete, authoritative guide to woodworking for readers of all skill levels. The books in the slipcase include: “”Book 1: Joinery,”” “”Book 2: Shaping, Veneering, Finishing,”” and “”Book 3: Furnituremaking,”” The techniques illustrated in these books are demonstrated step by step, with clarity and organization that allows readers to understand and carry out virtually any woodworking project.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.

I am surprised the the Hand and Eye combo by Tolpin didn’t make anyone’s list. I have also really found Chris Schwartz’s Anarchist’s design book very useful. Everything else that I really like is already in here somewhere; Moxon, Roubo, Estonia, Peart. The beginners book by Wearing is excellent, and I have taken to giving it to Eagle scouts at their Eagle Courts of Honor of late. (with an inscription about taking the raw stuff of life and developing the skills and tools to make from it what you need…); cheesy, I know, but it is a really good book to start folks off with.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.

I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
We offer top quality woodcraft products. When it comes to quality, dedication and a commitment to excellence we can't be beat! We have a large selection of online craft supplies for the hobbyist or the professional woodcrafter. We're dedicated to meet your craft and woodcraft products needs. Check out our online store and let us help you make your next woodcraft projects shine!
A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.
Line is defined by two points and is long relative to its width; it can be thick, thin, vertical, diagonal, straight or curved. Lines are often used to define a space, draw attention to a particular area and guide the viewer's eyes around a piece. To critically examine line in your design, look at the relationship between the lines, including ones which may be created in the negative space. How do they align? Do they lead your eye around the piece or do they stop abruptly and create disorientation?
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.

I have picked out a list of 9 books on woodworking that covers a wide variety of woodworking hobbies and techniques. I can personally vouch for these books, since I own most of them. These books will serve as valuable reference tools that can be used over and over. I’ve also checked the ratings and comments to make sure these books resonate with their readers. For your convenience, I’ve also included Amazon affiliate links so you can check out the Amazon reviews yourselves. Hope you enjoy the article and towards the end, I will ask you to share your favorite woodworking books.


Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.

A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.


A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
×