Even in today’s world of electric machinery, when most people were asked to name a woodworking tool, planes and scrapers would probably be at the top of the list. They are as useful now as they were years ago but, because of their electrified cousins, they are often overlooked in favour of a faster option. In this comprehensive book, John English explains what each type of plane is for, how to set it up for optimal performance and how to use it. The text is thorough and the photos are informative. All in all, this is a good read for a beginning or intermediate woodworker. Or a woodworker who simply never gave hand planes and scrapers a fair shake.
If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.
Line is defined by two points and is long relative to its width; it can be thick, thin, vertical, diagonal, straight or curved. Lines are often used to define a space, draw attention to a particular area and guide the viewer's eyes around a piece. To critically examine line in your design, look at the relationship between the lines, including ones which may be created in the negative space. How do they align? Do they lead your eye around the piece or do they stop abruptly and create disorientation?
There are simple jigs like a trammel baseplate and T-square, but you’ll also find a vacuum-clamping jig you can use to rout surfaces without clamps getting in the way, a dowel-making fixture, and router jigs to help you make fluted columns and even flamed finials. Bill also included several variations of router tables, including an ultimate table I built for my own shop.
I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.
The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.
My woodworking mentor, Robert Van Norman, studied under the esteemed woodworker James Krenov. Robert remembers many of JK’s wise words, especially “trust your eye”. When it was time for me to hear those words, I remember feeling such relief and permission to embrace my inherent perspicacity. Intuition is essential in the design and creation process, and for developing work that reflects the maker beyond his or her technical skill alone. At times, the craftsperson is called on to explain the aesthetics of his design and saying “it just feels right” doesn’t always cut it. This article covers seven common design considerations, their definition and how they are generally accepted and understood. Not only will the article help increase design vocabulary and awareness, but it may also assist in problem solving and recognizing the aesthetic strengths and weaknesses of a furniture piece.
Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.
Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
Colour Integration – Brian Newell creates a dynamic relationship between light and dark. Often, when contrast is employed, the focus is about the difference, but here Newell’s focus is about integrating the light and dark. This is achieved by using dark wood (Macassar Ebony), which also contains the same hue as the light wood (Pear), and by creating dark areas on the light wood from the negative space of the pierced carving and the pulls. (Photo by Yoshiaki Kato)
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
But I still wasn’t entirely satisfied with our list. I wondered if we’d read enough woodworking books as a staff to create a solid list. So we surveyed the readers of my blog (the results of that are on our web site), then asked many of the woodworkers who write for us to contribute lists of their favorite woodworking books. Theirs are below, in their own words (publishers have listed only on first reference; but if no publisher has been noted, the book is available on Google Books at books.google.com).
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.
Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!
This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.