The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
I have picked out a list of 9 books on woodworking that covers a wide variety of woodworking hobbies and techniques. I can personally vouch for these books, since I own most of them. These books will serve as valuable reference tools that can be used over and over. I’ve also checked the ratings and comments to make sure these books resonate with their readers. For your convenience, I’ve also included Amazon affiliate links so you can check out the Amazon reviews yourselves. Hope you enjoy the article and towards the end, I will ask you to share your favorite woodworking books.

For the most part, furniture restorers/refinishers/conservators in the United States lack the necessary hand-tool skills to do proper wood repairs. But avid readers of Popular Woodworking Magazine do possess the skills. Like me in the 1970s, you just need instruction on how to go about it. These books provide this. They greatly influenced the techniques I use in my shop, and many are shown in the “Repairing Furniture” video/DVD I made for Taunton.

Two for turners. Turners often develop needs and interests that are different than other woodworkers. Richard Raffan’s Complete Illustrated Guide to Turning offers one of the best overviews of the craft, as taught by a skilled artisan. As turners explore new ways to get a grip on different projects, they’ll appreciate Doc Green’s Fixtures and Chucks. This book explains how to get the most from commercial chucks, centers and faceplates and how to make your own.

I marked the holes by putting a dowel center in the end of a long piece of 1" dowel. Run it through the holes in the base plate, and bang on its end with a mallet. Rotate it a bit and bang it again, and repeat. Odds are the dowel center won't be precisely in the center of the dowel, so you'll be making a small ring of marks. The center of the hole is, of course, the center of that ring.

Woodworking books, plans and CDs allow you to study the methods of woodworking experts to reduce the learning curve on woodworking projects and save valuable time in the workshop. Reading a woodworking book is the easiest and least expensive way to learn from woodworking legends and craftsmen. Woodworking tips and lessons from masters like Tage Frid, Frank Klausz, Sam Maloof, Thomas Moser, Ian Norbury, Toshio Odate, Rude Oslnik, David Pye, and Gustav Stickley can be right at your finger tips. If your are interested in improving your hand tool skills or learning classic furniture-making techniques, we find Lost Art Press Books to be among the most important woodworking book collections we offer. With Christopher Schwarz as part of the writing and publishing team, you will be gaining access to one of the most creative and knowledgeable woodworkers around.
So since more than half the book is taken up with instruction, I thought there wouldn't be enough room for 40 projects. Thing is, the projects are mostly VERY simple and functional. There really does not seem to be any sort of eye towards craftsmanship and design. And they are almost all ugly. The picture frames included are literally the ugliest I've ever seen. Obviously, style is in the eye of the beholder, but I can't be making furniture to go in my home that looks like that, and my home is Ikea, Crate and Barrel, and Bombay to give you an idea.

I will admit, I'm not a pyrography genius. In fact the last time used a woodburning tool, it was Christmas Day and was about five years old. It didn’t go well. A lot has changed since then. The tools have improved, there is a large and growing group of wood­burning artists and there are great books to show you the basics and inspire you to pick up the art of pyrography. Woodburning with Style is the perfect book if you’re just learning. Not only will it teach you about the equipment available, it covers decorative tech­niques, lettering, portraits and more, before providing a chapter of inspirational projects and photographs to really get your imagina­tion going. Pyrography is an art in itself but can also be used in conjunction with turnings, carvings or furniture making.

When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.


The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.
Some posts may contain affiliate links. BestToolExpert.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon(.com, .co.uk, .ca etc) and any other website that may be affiliated with Amazon Service LLC Associates Program.
The wide variety of landmark furniture pieces, no matter the style, is what makes this book so visually stunning. That, and the fact that all of the 84 pieces that comprise the collection are beauti­fully photographed and a short description about each maker and piece is included. Many of the great makers from the last 100 years are covered – Sam Maloof, Wendell Castle, Tage Frid, George Nakashima – as well as many lesser known makers. If you read this book one hundred years from now, I’m sure it would be as thought provoking as it is today. These are 84 great pieces, and this is one great book. 
efore you cut your first board, you must have a design to achieve the results you're after. To create a workable design, you must understand important properties of the wood you will be using, methods for joining that wood, typical construction techniques that are appropriate for the type of project you are building, styles of craftsmanship that will enhance and compliment the environment where this project will be used, and finally how to think through and plan a project.
The Fall 2018 issue of Scroll Saw Woodworking & Crafts features a variety of projects, patterns, and features, as well as interesting techniques. This issue is a part of the regular magazine subscription. It is also available from your favorite retailer or from Fox Chapel Publishing,www.foxchapelpublishing.com, 1-800-457-9112.   In This Issue Scroll down for a […]
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.

I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.

Finishing is often an afterthought and spraying a finish isn’t exactly the first technique discussed when the topic does come up. While it’s often easier to wipe on a couple of coats of finish and be done with it, there are times when spraying a finish makes the most sense. There are many advantages to spraying a finish but there are some drawbacks too. Spray Finishing Made Simple does what it claims – it takes an imposing, unfamiliar topic and makes sense of it. This book is for the first-time spray finisher, as it starts with the basics and progresses through the stages. Don’t let the unknown stand in your way if you’re interested in learning about spraying. Pick up this book and get spraying.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.
I wanted the left edge of the jaw of the front vise to be flush with the left edge of the top, the right edge with the left edge of the left front leg. So the amount of overhang on the left depends upon the width of the front vise jaw. The width of the jaw is, at a minimum, the width of the plate that supports it, but it's normal to make the jaw extend a bit beyond the plate. How far? The more it extends, the deeper a bite you can take with the edge of the vise, when, for example, you are clamping the side of a board being held vertically. But the more it extends, the less support it has. I decided to extend by 1-12", which gives me a 2-1/2" bite, and which should still provide solid support, given that the jaw is 1-1/2" thick. This means the top needs a left overhang of 12-1/4".
“The Complete Guide to Woodworking features detailed plans for 40 stunning projects for woodworkers of all levels, plus more than 1,200 step-by-step illustrations. It also includes expert information on setting up a workshop, safety, how to use and look after tools, and much more. For beginners and experienced woodworkers alike, this is the ultimate step-by-step guide.
I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
I marked out the one hole location, drilled a shallow 1/16" hole into the top. I then put a 1/16" bit through the hole in my template and into the hole I had just drilled. I lined up the template, and drilled a second hole, then put another bit through that. From then on, I worked entirely from the template. With two bits through the holes pinning the template in place, the other holes in the template would be precisely located (or so the theory goes) on a 4x4" grid.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
“Woodworking in Estonia” by A. Viires (National Technical Information Service). This is our share of the booty from the cultural exchanges of the Cold War years. The Soviets got models of our nuclear subs, and we got one of the best books on folk woodworking ever. Aside from showing how to make everything from wooden wheels to bentwood cheese boxes, this book is also an education in the way Eastern European history gets written. Imagine Eric Sloane dividing early American woodworking into feudal, capitalist and socialist periods!
The best way to use this article is to visually break the furniture piece down with reference to the categories listed. On a piece of paper, write down the main focus or core of the piece and place it beside the project. With a critical eye, question whether all the elements support the main goal. Ask why you have designed it this way. For example, if the main focus is to have a comfortable chair, you might want to consider which lines, texture or colours visually inspire people to think the chair is comfortable and stable even before they sit in it.
Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.

If you decide upon construction lumber, you want kiln dry lumber. Green lumber will warp on you as it drys. Dig through the stacks and pick out the straightest, cleanest pieces. Generally, the boards that are sitting loose on the stack are those that other people left behind, as they sorted through looking for better. Be prepared to move them out of the way, and to dig down to the better stock. Be nice, though, and put everything back when you're done.
Tapping the knowledge of dozens of top-shelf woodworkers, Scott Landis’s The Workbench Book, and Jim Tolpin’s The Toolbox Book are filled with inspirational photos and drawings that you can use to enhance your workbench and tool storage needs. John White’s Care and Repair of Shop Machines completes the workshop triumvirate. The author’s straightforward advice for repairing and setting machinery will help you make the most of every machine in your shop.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.

Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.


Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.

To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.


With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The base needs to be as wide as the sum of width of the guide strip and the distance from the edge of the shoe, plus a bit extra, With my saw, the overhang is 3-1/2", so I made my guide strip 5-1/2" wide. The distance between from the edge of the shoe to the blade is about 4-1/2", so the base needs to be at least 10" wide. Since I was working with a 24" wide sheet, I just sliced it down the middle.

The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.

There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
I was raised by crafty people. In every sense of the word. Just kidding! My parents were lovely people who loved to work with their hands in their spare time. For a brief period of time as a kid my mom even earned a living by selling her wares at local craft fairs, but for the most part their crafting was a hobby that filled our home with beautiful and practical pieces of woodworking.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.

I like the idea of re-inventing the wheel. I choose to believe that while others may have considered these improvements, they just never got around to trying them out. Brain gets bored with status quo. So, I try to keep Brain happy with the occasional foray into uncharted territory. And I must say Brain has had some really good results. Thanks, in part, to you, and the Roy. You never know where a good idea might come from so I’ll check in once in a while. That and make sure to build it in Sketchup first.

×