This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
This book addresses a key dilemma of the beginning woodworker: how do you build good projects without the basic shop furnishings to get the job done? And, why struggle with makeshift workshop equipment when you can create your own? Now you have the guidance of an expert woodworker to help you build workshop basics that you will use for years to come.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
If you’re even the slightest bit interested in the history of Japanese furniture, you will love this thorough collection of chests. The attention to detail is astounding, the photographs glorious and the historical insight intriguing. This is exactly what you would expect from a book that covers such a proud history of chest mak­ing on the land of the rising sun. Almost 100 pages of colour plates are complemented by information on typical construction materials, finishing techniques and regional charac­teristics. This book will please the antique collector, interior designer or wood­worker equally. 
I will admit, I'm not a pyrography genius. In fact the last time used a woodburning tool, it was Christmas Day and was about five years old. It didn’t go well. A lot has changed since then. The tools have improved, there is a large and growing group of wood­burning artists and there are great books to show you the basics and inspire you to pick up the art of pyrography. Woodburning with Style is the perfect book if you’re just learning. Not only will it teach you about the equipment available, it covers decorative tech­niques, lettering, portraits and more, before providing a chapter of inspirational projects and photographs to really get your imagina­tion going. Pyrography is an art in itself but can also be used in conjunction with turnings, carvings or furniture making.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
The person who coined the saying, “The more things change, the more they stay the same,” just might have been a woodworker. Admittedly, new tools and materials have made certain operations faster, safer, and easier, but if a woodworker from the 1900s could visit your workshop, he’d have a tougher time with the K-cup coffeemaker than the table saw. That’s because the basic tenets and tools of woodworking are almost timeless.
Olympia Tools is a bit of a lesser known manufacturer. While they offer a wide range of products for a variety of construction fields, they are definitely more of a budget option. That said, Olympia Tools is one of the few brands that manages to produce a reasonable quality at a low price which makes them a solid choice for customers looking to get the best bang for the fewest bucks.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
If you’re more interested in working with wood rather than machining it, you will be relieved to learn that expensive powered machinery isn’t required to build furniture. You can also forget the dust masks, face shields and hearing protection since many of the safety concerns related to woodworking—the use of power tools—are eliminated. In this book, you’ll learn to set up a hand-tool woodworking shop, then discover the toolset, practice the skillset, and understand the mindset—effectively completing a comprehensive course in hand-tool woodworking.
The Fall 2018 issue of Scroll Saw Woodworking & Crafts features a variety of projects, patterns, and features, as well as interesting techniques. This issue is a part of the regular magazine subscription. It is also available from your favorite retailer or from Fox Chapel Publishing,www.foxchapelpublishing.com, 1-800-457-9112.   In This Issue Scroll down for a […]
Happy bench building folks. I hope you make it your own and not worry too much about what someone else thinks it should be. Use the rules as a guideline, they have validity, but make it your own in the end. If the rules fit you that’s great, if they don’t quite fit you then make it to fit yourself. It’s you using it, not some guy making a nice living off of telling you how he thinks you should do it. One size does not fit all. Never has, never will.
If you’re more interested in working with wood rather than machining it, you will be relieved to learn that expensive powered machinery isn’t required to build furniture. You can also forget the dust masks, face shields and hearing protection since many of the safety concerns related to woodworking—the use of power tools—are eliminated. In this book, you’ll learn to set up a hand-tool woodworking shop, then discover the toolset, practice the skillset, and understand the mindset—effectively completing a comprehensive course in hand-tool woodworking.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.
For the most part, furniture restorers/refinishers/conservators in the United States lack the necessary hand-tool skills to do proper wood repairs. But avid readers of Popular Woodworking Magazine do possess the skills. Like me in the 1970s, you just need instruction on how to go about it. These books provide this. They greatly influenced the techniques I use in my shop, and many are shown in the “Repairing Furniture” video/DVD I made for Taunton.
Another aspect that might irk some buyers is the fact that the capacity of this bench is less than great outside of weight. The top’s surface area is a bit on the smaller end, though its length is more in line with larger models. The width though is less than two feet which can limit some projects. Similarly, the vice capacity is the second smallest on our list at 4 ½”, though this too can be modded with optional additions.
×