Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
The ultimate in cabinet design inspiration. Fantastic photographs, coupled with a little bit of information on each piece, is more than enough to give you that nudge to go ahead and try something different with your next cabinet. From surface decoration to using different materials, non-stan­dard shapes to unique finishes, there’s a taste of everything for everyone. You won’t learn how any of these pieces are made but it will make you wonder. 500 Cabinets is the extension of the “500” series by Lark Books and, like the rest, this one will delight readers of any skill level. It will even interest those who know nothing at all about woodworking. There are many Canadian makers included. This is a col­lection I’ll refer to over and over again, because each time look through it I’ll do so for a different reason, getting some­thing different each time. This one rarely makes my bookshelf … it’s always right on my desk. And of the collection here, this is my favourite.

Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
If you’re looking for something fun, funky and functional, you’ll find it in your Kotula’s catalog. We’re relentless in our pursuit of the good stuff which means you can count on your Kotula’s catalog to be your personal cornucopia of cool. Kotula’s has gifts and gizmos, tools and time savers, low prices and great value. Request your free catalog today.
In order to complete your transaction, we will share the name, billing and shipping address and other order information associated with your purchase with the publisher or magazine vendor. Your name and address will also be shared with a circulation-auditing organization. We may share your e-mail with the publisher, but you can control how it will be used in Subscription Manager. We will not share your credit card information. Offers on this page are introductory. See Details.
Put the upper panel of MDF on your glue-up surface, bottom side up. Put the bottom panel of MDF on your other surface, bottom side down. (The panel with the holes drilled in it is the bottom panel, and the side that has the your layout diagram on it is the bottom side.) Chuck up in your drill the appropriate driver bit for the screws your using. Make sure you have a freshly-charged battery, and crank the speed down and the torque way down. You don't want to over-tighten the screws, MDF strips easily.
David Ellsworth has been refining his style for years and now, with his first book, you get to see exactly how the “grandfather” of turning does it. Offering more than just turning infor­mation, a number of chapters in this book discuss top­ics that non-turners will be interested in. Having said that, turning is the main focus here. Ellsworth speaks to what he knows best – an open bowl, a natural-edge bowl and the highlight of the book, a hollow vessel with an impossibly small opening. He also covers basics like sharpening, design, finishing and more. One chap­ter even details the stresses that turning puts on the human body and how to get the most from this overlooked “tool”. A crucial read for a wood-turner and an enlightening read for a woodworker. 

Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference


The jaw for the front vise needed to be 10" long - to span the distance from the leg to the end of the top, 1-1/2" thick - to allow for benchdog holes to be drilled in it, and 5" tall. The end vise was mounted 3/4" lower than the front vise, and the screw and guide rods were thicker, so its jaws needed to be at least 6-1/2" tall. Again, they needed to be 1-1/2" thick to allow for benchdog holes, and 23" long to span the width of the bench.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
“This hardcover book with internal spiral binding is 6.5in x 8in, a perfect size for carpenters and woodworkers to keep near their workbench or toolbox for quick access.The design of this book allows it to lay open flat, which allows for easy and frequent reference, and the interior photographs, illustrations and diagrams, make the learning process simple and fun for beginners, and provides useful tips for more advanced readers.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking

Shape is critical to the ultimate success or failure of a piece of furniture. Knowing this, custom-furniture maker Lonnie Bird has taken the complex subject of shaping and in this book made it accessible to every woodworker. He guides the reader toward first visualizing, then drawing a shape, and then choosing the appropriate tool for creating it. Shaping techniques of all kinds are covered here — from the simplest ones to more complex bending and carving.”
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
Woodworking Basics presents an approach to learning woodworking that has proven successful for hundreds of people who have taken the author’s introductory course over the past 20 years. Peter Korn’s method helps new woodworkers learn the right techniques from the beginning.More experienced woodworkers can use it to master the classic furniture-making skills key to fine craftsmanship. Korn includes two attractive and useful projects — a small bench and a side table with a door and drawer — providing you the opportunity to practice skills and develop confidence with tools.
Audubon Birdhouse Book: Building, Placing, and Maintaining Great Homes for Great Birds Not only does this book offer great instructions and pictures on building birdhouses, but it also teaches you what makes for a safe and successful birdhouse for our little feathered friends. Lots of tips on where to place birdhouses and how to maintain them. This book is very much focused on the bird enthusiast and not so much the aesthetics of birdhouses.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
I find furniture takes on new meaning when separated from the sterility of an art museum (such as the Philadelphia Museum of Art’s American Wing. Maybe that’s why I prefer the museum’s period rooms). Jeffrey P. Greene’s book is perhaps my favorite of recent period woodworking texts for its ambition and helpful exploded diagrams of furniture in its appendix.
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.
×