I clamped the top to the side of the base, as I had done before, so that the edge with the knot would be easy to work with. I mixed up some ordinary five-minute epoxy and added just a touch of black epoxy pigment. I applied this freely. After about twenty minutes I checked on it and found that in the deepest spot the void wasn't entirely filled, so I mixed up another batch and added more. After that had cured for a bit I eased the top to the floor and applied a coat of oil to the bottom side. I planned on attaching the base to the top the next day, and I wanted the bottom side oiled to keep it from absorbing moisture.

I’m building my second bench. I built the first years ago with wood from old machinery pallets – mostly oak and maple. Mortised the legs into the base, and pegged ’em with 1″ dowels. Of course, the legs warped a bit, but that made everything tighter and stronger. The top is 2″ thick Ash, one board cut in half and joined side to side. Wrapped a maple apron around the top, and I think I screwed the top from underneath to the leg braces. Solid. Over time, built a cabinet under for 3 drawers and a small cabinet door. Works for me.

In order to complete your transaction, we will share the name, billing and shipping address and other order information associated with your purchase with the publisher or magazine vendor. Your name and address will also be shared with a circulation-auditing organization. We may share your e-mail with the publisher, but you can control how it will be used in Subscription Manager. We will not share your credit card information. Offers on this page are introductory. See Details.

Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Another comprehensive book by Taunton Press, Wood Flooring is extremely informative, not to mention visually compelling. From subfloors to finishing, and everything in between, you can be sure this is the only book you will ever need on the subject. My favou­rite chapter was on inlays and curves: using jigs and templates to add circular inlays to a floor, laying out and installing laminated curves, even working with stone and metal inlays … there’s a lot to learn in that one chapter alone. Much of it could be adapted to making furniture. If you want to lay a basic wood floor this book will help you add lasting value and beauty to your home. If you’re looking to one-up your super handy DIY brother-in-law, you can start here too.
This book addresses a key dilemma of the beginning woodworker: how do you build good projects without the basic shop furnishings to get the job done? And, why struggle with makeshift workshop equipment when you can create your own? Now you have the guidance of an expert woodworker to help you build workshop basics that you will use for years to come.

Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.

Of course, I, on the other hand, with my Ikea oak countertop, probable went overboard in the other direction. Since I needed to trim the countertop to width,I figured I'd take off a couple of 1/2" strips to use for edging the MDF. I clamped the countertop to my bench base, and used the long cutting guide. I'd asked around for advice on cutting this large a piece of oak, and was told to try a Freud Diablo 40-tooth blade in my circular saw. I found one at my local home center, at a reasonable price, and it worked very well.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.
Ernest Joyce, Revised & Expanded by Alan Peters, Technical Consultant, Patrick Spielman It’s been the number-one book on the subject for most of the 20th century; the encyclopedia with the latest information on the tools, techniques, and processes. This thorough…edition introduces furniture construction, design, and restoration. Choice color photographs accent…abundant black-and-white photographs and drawings…an invaluable reference
A bewildering variety of tools, clever marketing copy, and lack of knowledge can lead even the most determined new woodworker to make many unnecessary purchases, causing frustration or retreat. Written for true beginners, Your First Shop offers inspiration and encouragement, guiding readers toward smart tool choices by providing realistic, reliable information. Best-selling author Aimé Ontario Fraser started working with wood in high school, and has taught extensively in workshops and classes since. Your First Shop brings that experience to readers. Woodworkers of every taste can find a shop style that works for them in one of the book’s four sections: The Essential Shop, The Basic Shop, The Efficient Shop, and The Well-Rounded Shop. Topics include how each tool is used and what it is used for. The book also offers extensive advice on choosing a location for the shop, maximizing available space, and planning for future expansion.
The top is supported by the top ends of the legs and the top sides of the top stretchers. Stand your legs on end on a flat surface (like my door) and see if they wobble. If you have an end that isn't quite stable, use it as a foot, where the leveler will make it's flaws unimportant. Check the top edge of each stretcher for straightness. If one has a bit of a bow, use it for a lower stretcher. It's less critical that the shelf be well supported along its length.
Stop it. Really. I mean it. Pick a height between your thigh and waist that seems right. You’ll adapt. Don’t worry about your back. You’ll adapt. If you are really uncertain, make it a little taller and then cut down the legs. After a decade or so, your work habits will put a magic number in your head. You’ll have built enough furniture that you will know your number. Until then, pick a number.
This bench suffers from no such limitations as it provides an incredibly solid and stable workspace, albeit in a somewhat stripped down version. In terms of performance, Sjobergs tops our list at providing 80 lbs of weight capacity. This is one of the more quantifiable measurements to determine the quality of a work bench’s craftsmanship. This is achieved by using thick pieces of European birch wood and working it without using lower end joints – like butt joints.