Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
The Rockler Woodworking and Hardware free catalog features over 140 pages of our best products mailed directly to your door. You should receive your catalog in 1 to 2 weeks, depending on your location. In the meantime, you'll find all of the products in our catalogs here on our website. Just choose one of the department links on your left, or enter a keyword search.
In the "Getting Started with Woodworking" video, the holes through the 4x4's were drilled from the back. That is, they start on the side opposite the precisely-positioned mark, and drill through to hit it. If they can do this, more power to them, but I can't drill through 3-1/2" of wood to emerge at a precise mark without a drill press - and not always then.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.
1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Audubon Birdhouse Book: Building, Placing, and Maintaining Great Homes for Great Birds Not only does this book offer great instructions and pictures on building birdhouses, but it also teaches you what makes for a safe and successful birdhouse for our little feathered friends. Lots of tips on where to place birdhouses and how to maintain them. This book is very much focused on the bird enthusiast and not so much the aesthetics of birdhouses.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.
I am surprised the the Hand and Eye combo by Tolpin didn’t make anyone’s list. I have also really found Chris Schwartz’s Anarchist’s design book very useful. Everything else that I really like is already in here somewhere; Moxon, Roubo, Estonia, Peart. The beginners book by Wearing is excellent, and I have taken to giving it to Eagle scouts at their Eagle Courts of Honor of late. (with an inscription about taking the raw stuff of life and developing the skills and tools to make from it what you need…); cheesy, I know, but it is a really good book to start folks off with.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
Of course, few benches can be ideal, and this one does have some drawbacks. That being said, most of the disadvantages of this bench are minor annoyances rather than deal breakers. For instance, this bench does not include any kind of storage whatsoever. Though, it does have the option of adding numerous additional features like a storage area. Still, for the bench, you would expect a drawer at the very least, maybe a shelf below the main table area.