We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Editor’s note: In the September/October 2017 issue (which mails to subscribers on Aug. 1), we have an article from up-and-coming makers on the books that have influenced their work and woodworking philosophy. Below is a similar article we ran in June 2011, asking established makers what they felt were the most important woodworking books, plus we included our staff picks. I’ve linked to our store for the ones we carry, some of which are now available only as eBooks, and to those from Lost Art Press. For titles that are out of print, I recommend Bookfinder.com, or better yet, your local used bookstores. Or, ya know, the library.
But I still wasn’t entirely satisfied with our list. I wondered if we’d read enough woodworking books as a staff to create a solid list. So we surveyed the readers of my blog (the results of that are on our web site), then asked many of the woodworkers who write for us to contribute lists of their favorite woodworking books. Theirs are below, in their own words (publishers have listed only on first reference; but if no publisher has been noted, the book is available on Google Books at books.google.com).
When this book showed up at my studio I was very sceptical. Yet another “book of everything”? But after spending only five minutes skimming through it, I learned about a couple of storage ideas my shop needed, some cool new jigs that would come in handy and a few tricks to make my time in the shop more enjoyable and productive. There will be hundreds of ideas in here you will have no interest in whatsoever, but that’s all right … there are over 650 ideas in total, so some are sure to tickle your fancy.
As I try to improve as a woodworker and artist, I really want every piece to be better than my last. But this piece will always hold a special place in my ❤️ This table is made of 1250+ pieces of recycled skateboards and walnut, but If you count the individual veneers of the recycled skateboard pieces then it’s made of over 6,800 pieces of wood. 📷 @fvcksandflamingos 😘 #upcycledskateart
For an entertaining read (and proof that woodworkers lead interesting lives), treat yourself to Nancy Hiller’s Making Things Work: Tales from a Cabinetmaker’s Life, and George Frank’s Adventures in Wood Finishing. These two biographical books are beautifully written and offer similarly lively accounts of the adventures that come from making a living as a woodworker. As you spend time with Nancy and George, we think you’ll enjoy the stories that come with the sawdust
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
Tools: I am inspired by tools, whether the tool is a good chef’s knife, a watercolor paintbrush or a lowly marking gauge. I find 18th-century tools particularly beautiful and elegant in their simplicity. To openly admit I am inspired by my tools makes me somewhat of a kook. But here, amongst friends, I suspect I am not alone. I’ve copied many tools in these books and sought tools that resembled these and been a happier person for it.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The base needs to be as wide as the sum of width of the guide strip and the distance from the edge of the shoe, plus a bit extra, With my saw, the overhang is 3-1/2", so I made my guide strip 5-1/2" wide. The distance between from the edge of the shoe to the blade is about 4-1/2", so the base needs to be at least 10" wide. Since I was working with a 24" wide sheet, I just sliced it down the middle.
Copyright © 2018 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
When you're working with linseed oil, never -- I mean NEVER -- leave used rags lying around. Hang them up outside, away from anything combustible, and where there's enough air circulation to keep them cool. Or put them in a bucket of water, and hang them outside later. If you're just setting a rag down for the moment, set it out flat, without folds, on something non-flammable. Hanging outside in the breeze, the oil in the rags won't retain heat while they oxidize. For the oil to completely oxidize can take in a couple of days, if it's warm, or more than a week, if it's cold and rainy. When fully oxidized, the oil will be solid and the rags will be stiff. At that point, they're safe, and can be thrown in the trash. Toss them in the trash before that, and you might as well say goodbye to your garage.
Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
Anyway, the reason I bring all this up is not to brag, but to alert you to a great deal. Recently, we had a chance to acquire the last print copies of these five books, which were sitting, overlooked, in a warehouse. The books mainly have black and white interiors and beautiful hand-drawn illustrations. And every one offers more than 300 pages of excellent advice on woodworking projects and techniques.
As a teacher I find Ernest Joyce’s “The Technique of Furniture Making” (Batson) invaluable, ’tho it is as far away from an enjoyable read as possible. Similarly Bob Wearing’s “Essential Woodworker” (Lost Art Press). Bob is one of the only people who ever gave insight into traditional English technique. I believe the lack of similar books is due to the apprenticeship tradition of teaching, where nothing was ever written down.
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.